Sagemcom [email protected] 2705 Manual [Español]

F @ ST 2705

Quick Installation Guide

Sagemcom thanks you for choosing the F @ ST 2705 router and we hope the product meets all your expectations.
The F @ ST 2705 ​​is a product that operates on ADSL technology, respectively in POTS (ITU G.992.1 / 3/5 – Annex A) and ISDN (ITU G.992.1 / 3/5 – Annex B)
The product includes four Ethernet ports (LAN 1 to LAN4) and an ADSL interface.

CE Certification:
The CE marking certifies that the product complies with all essential requirements of the 1999/5 / EC standard for radio and telecommunications equipment, and safety standards 2006/96 / EC and 2004/108 / EC in compatibility defined by the European Parliament with the aim of reducing and protecting users’ health.

The F @ ST 2705 ​​is also certified in ANATEL (National Telecommunications Agency).

 

Copyright © Sagemcom Broadband SAS
All rights reserved.
Sagemcom is a registered trademark.

Windows® is a registered trademark of Microsoft Corporation.

Package Contents
Before installation, make sure your package has all of the following:

Safety Instructions
This equipment operates on a secondary basis, that is, it is not entitled to protection against harmful interference, even from stations of the same type, and may not cause interference to systems operating on a primary basis.

Power Supply

• Do not leave the router on the power supply.
• The router comes with its own power supply in the box and should be used exclusively with it.
• This adapter class (II) does not need to be grounded (ground wire). The connection to the mains must comply with the instructions given on the label.
• Use an electrical outlet near the router. The power cord has a length of 1.5 m.
• Connect the power supply to prevent accidents.
• The router is designed to be connected to a GG- (ground-ground) or GN- (ground-neutral) both types of power grids.
• The router is not designed to be connected to an IT installation.
• Protection against short circuits and leaks between phase, ground and neutral should be provided
by the local electrical installation. The power supply circuit for the equipment
shall be equipped with 16 A, overcurrent protection and differential protection.
• Connect the router to the wall outlet.

Local conditions
When choosing an appropriate location, you will preserve the life of your product. Verify that the location chosen has the following characteristics:
• Install and use the router inside a building.
• The ambient temperature must not exceed 45 ° C.
• The router can be placed on a table or attached vertically to your wall.
• Do not expose the router to strong sunlight or place it near a heat source.
• Do not place the router in an environment where it can be steamed.
• Do not expose the router to water.
• Do not cover the router with a casing.
• Do not use the router or its peripherals in outdoor installations.

Maintenance
• Never open the casing. This should be done only by trained personnel equated by the supplier.
• Do not use liquid or aerosol to clean the product.

Connection
Connecting your router

Connect your router as shown in the figure below:



Monitoring the router

You can monitor the router as follows:
• status of the LEDs on the front and left panels of the router.
• using the built-in router “DSL Router” available in the configuration tool.

LED status on the front panel

 

Buttons in the left panel

 

Accessing the modem
Open your Internet browser and enter the address http://192.168.1.1. Right after you use the credentials to access the device:
User: admin
Password: The password is located on the label behind the modem

 

Performing the factory reset
To perform the factory reset of the machine click on Management> Settings> Restore Default and click on Restore Default Configuration. This option will bring the router with the same settings from the factory.

Wi-Fi Network
To set up your Wi-Fi network, choose the Network Name (SSID), the security level (encryption), and the password of your choice.
Types of encryption: WPA (high security) or WEP (medium security)

Click -> Next.

Your modem is pre-configured with the following data:
• Network Name: The network name is located on the label behind the modem.
• Encryption: WPA2-PSK
• Password: The network password is located on the label behind the modem.

At any time, you can return to the default settings of your modem. Just click the reset button on your modem.

 

 

All rights reserved. The information and specifications included are subject to change without notice. Sagemcom Broadband SAS attempts to ensure that all information contained herein is correct but does not accept responsibility for error or omission. Non-contractual document. All trademarks are registered by their respective owners. Simplified joint stock company – Capital 35 703 000 euros – 518 250 360 RCS Nanterre

[email protected] 2705

Guia Rápido de Instalação

Sagemcom agradece por escolher o roteador [email protected] 2705 e esperamos que o produto atenda todas suas expectativas.
O [email protected] 2705 é um produto que opera na tecnologia ADSL, respectivamente na POTS (ITU G.992.1/3/5 – Anexo A) e na ISDN (ITU G.992.1/3/5 – Anexo B)
O produto inclui quatro portas Ethernet (LAN 1 à LAN4) e uma interface ADSL.

Certificação CE :
A marca CE certifica que o produto está de acordo com todos os requerimentos essenciais da norma 1999/5/EC para equipamentos de rádio e telecomunicações, e as normas 2006/96/EC em segurança e 2004/108/EC em compatibilidade eletromagnética, definido pelo parlamento Europeu com o objetivo de reduzir e proteger a saúde dos usuários.

O [email protected] 2705 também está certificado na ANATEL (Agência Nacional de Telecomunicações).

 

Copyright © Sagemcom Broadband SAS
Todos os direitos reservados.
Sagemcom é uma marca registrada.

Windows® é uma marca registrada da Microsoft Corporation.

Conteúdo na embalagem
Antes da instalação, verifique se a sua embalagem possui todos os itens abaixo:

Instruções de segurança
Este equipamento opera em caráter secundário, isto é, não tem direito a proteção contra interferência prejudicial, mesmo de estações do mesmo tipo, e não pode causar interferência a sistemas operando em caráter primário.

Fonte de alimentação

• Não deixar o roteador sobre a fonte de alimentação.
• O roteador está acompanhado com sua própria fonte de alimentação na caixa e deve ser usado exclusivamente com a mesma.
• Esta classe de adaptador (II) não precisa ser aterrado (fio terra). A conexão para a rede elétrica deve cumprir as indicações dadas na etiqueta.
• Use uma tomada elétrica perto do roteador. O cabo de alimentação tem o comprimento de 1,5 m.
• Ligue a fonte de alimentação de modo que evite acidentes.
• O roteador é projetado para ser conectado a um GG-(terra-terra) ou GN-(terra-neutro) ambos tipos de redes de energia.
• O roteador não foi projetado para ser conectado a uma instalação elétrica com IT.
• Proteção contra curto-circuitos e vazamentos entre a fase, neutro e terra deve ser fornecida
pela instalação elétrica do local. O circuito de fornecimento de energia para o equipamento
deve ser equipado com 16 A, proteção de sobrecorrente e proteção diferencial.
• Conecte o roteador perto da tomada.

Condições locais
Ao escolher um local apropriado, você vai preservar a vida útil do seu produto. Verifique se o local escolhido tem as seguintes características:
• Instalar e usar o roteador dentro de um edifício.
• A temperatura do ambiente não deve ultrapassar 45°C.
• O roteador pode ser colocado sobre uma mesa ou fixado verticalmente em sua parede.
• Não exponha o roteador à luz solar forte ou colocá-lo perto de uma fonte de calor.
• Não coloque o roteador em um ambiente onde ele pode ser submetido ao vapor.
• Não exponha o roteador à água.
• Não cubra o roteador com um casing.
• Não use o roteador ou seus periféricos em instalações ao ar livre.

Manutenção
• Nunca abra o casing. Isto deve ser feito somente por pessoas treinadas  equalificadas pelo fornecedor.
• Não use líquidos ou aerossol para limpar o produto.

Conexão
Conectando seu roteador

Conecte seu roteador como mostra na figura abaixo:



Monitorando o roteador

Você pode monitorar o roteador da seguinte forma:
• estado dos LEDs nos painéis frontais e esquerdo do roteador.
• usando o roteador embutido “Router DSL”, disponível na ferramenta de configuração.

Estado dos LEDs no painel frontal

 

Botões no painel esquerdo

 

Acessando o modem
Abra seu navegador de internet e digite o endereço http://192.168.1.1. Logo após use as credenciais para acessar o aparelho:
Usuário: admin
Senha: a senha está localizada na etiqueta atrás do modem

 

Realizando o Reset de Fábrica
Para realizar o Reset de Fábrica do equipamento clique em Gerenciamento > Configurações > Restaurar Padrão e cliquei em Restaurar Configuração Padrão. Essa opção irá trazer o roteador com as mesmas configurações vindas de fábrica.

Rede Wi-Fi
Pra configurar a sua rede Wi-Fi, escolha o Nome da Rede (SSID), o nível de segurança (criptografia) e a senha de sua preferência.
Tipos de criptografias: WPA (alta segurança) ou WEP (média segurança)

Clique em -> Avançar.

Seu modem já vem configurado de fábrica com os seguintes dados:
• Nome da Rede: o nome da rede está localizado na etiqueta atrás do modem.
• Criptografia: WPA2-PSK
• Senha: a senha da rede está localizada na etiqueta atrás do modem.

A qualquer momento, você pode voltar às configurações de fábrica do seu modem. Basta clicar no botão Reset do seu modem.

 

 

Todos os direitos reservados. As informações e especificações incluídas estão sujeitas a alterações sem aviso prévio. Sagemcom Broadband SAS tenta garantir que todas as informações contidas neste documento estão corretas, mas não aceita responsabilidade por erro ou omissão. Documento não contratual. Todas as marcas são registradas por seus respectivos proprietários.Sociedade por ações simplificada conjunta – Capital 35 703 000 euros – 518 250 360 RCS Nanterre

https://fccid.io/ANATEL/00950-16-05950/Manual/56C91D72-5A66-4297-A26F-4BBF7ED94E81/PDF

This manual is in spanish so it may be more difficult to convert– just do your best!

ProScan DZ09 PBTW360 Smart Watch User Manual

ProScan PBTW360

SMART WATCH
USE MANUAL

Please read the manual before use
USE MANUAL FOR SMARTWATCH
PBTW360

1. SAFETY WARNING
Before use, please read the user manual carefully.
– Only support the standard battery, charger and accessories we approved, we won’t take any responsibility for any consequences caused by the use of third party accessories.
– Prohibit the unauthorized dis-assembly of watch phone.
– No mechanical vibrating and shaking. No kicking the screen by tool.
– No using solute to clean the shell, such as benzene, thinner or alcohol. No touching the watch phone with corrosive chemicals and so on, but with a clean textile to clean it softly.
– No exposing the watch phone under the sunrise or the place with smog and dust.
– Keep the phone in dry. No using in the wet environment such as bathroom. This watch is not water proof and is strictly prohibited to rain and moisture.
– Please put the watch phone in a safety place out of the reach of children to avoid any dangerous happening. The information in this document won’t be modified or extended in accordance with any notice.
– The watch should be charging 2 hours at least before use.

2. PRODUCT DETAILS
2.1 Product details

Power button: -Power on / off by long press the button, Awaken / turn off the screen, Back to main menu by short press.
-USB port: Charging
-Touch screen: each function (main menu) will be shown and displayed.

2.2 Products quick into

You can enter into next page by sliding screen to the left, and return to last page by sliding screen right, enter into the notice board after sliding from up to down, and return to main mean from down to up. It will be in mistake for a click if the drag distance too short.

2.3 Clock Display


Setting Method:
Power on, when the phone in clock mode, please click middle screen to choose the desired clock interfaces.

3. PRODUCT QUICK USE
3.1 Download the sync software
Scan below QR code to download the APP(only for android phone).

If you downloaded thesoftware before, please check if the version is the newest one to ensure all function normal use. And please update the software when have new version.

3.2 Install and use the sync software
Android Application installation:
Please install the android application in your smart phone. You can storage it into your phone memory or install by Sync assistant.

Android applications usage(already installed):
(Smart phone) Setting – Accessibility – Enter into Bluetooth notice (service), enabled this service, (please choose “sure” when shown a warning notices) the application runs on the background automatically. Click the Bluetooth notice and choose the Notification service, select your Personal or System application in Notify application. Telephone service in including SMS, incoming call and seek watch.

Notice:
Please don’t shut the Bluetooth notify service when you are clearing software by background or close background application software. It will affect the Sync function between watch and phone if shut it.

3.3 Bluetooth connectivity and sync function
3.3.1 From phone to Watch
Phone settings – turn on bluetooth – search for devices, please click pair devices when found the watch, and also choose “yes” in your mobile phone, paired done.( The Bluetooth device name is PROSCAN-PBTW360) Please choose “sure” when there is phone book request, meanwhile you’d better to choose “no remind again”, this is convenience when you connect next time (without remind again).

3.3.2 From watch to phone
BT Dialer-Search new device-found your smart watch (such as s9500)-connect.
Note:the mobile phone need to turn on the bluetooth and allow to be searched by around bluetooth products.

3.4 Basic Functions
– Message: Sync phones or watch message.
– Bluetooth: Set the Bluetooth, turn on / off.
– Call logs: You can check your phone call records after you connect with the Bluetooth. Shown all records including miss call, dialed calls and receive call. You can check the date, time and phone number of the miss call after you choose it, but only can call this number.
– Remote Notifier: When there is SMS, incoming messages from QQ and other applications on the connected phone, the watch phone will alert you to read them.
–  Remote capture: Use phone camera take pictures; but remote by watch. Its need switch on the camera of phone in advance.
– Anti lost: Watch seek phone, or phone seek watch.
–  Setting: Notice-sets clocks display and theme in phone setting; In the security Settings, the safe code Is 1122
– Pedometer: It can be adopted as a tool to avoid insufficient or excessive exercise by measuring calories of calories consumption based on collected data, such as number of steps, distance, speed, time, etc to control exercise. If you want return to main menu but keep pedometer during the exercise, please press the power button.
–  Sleep Monitoring: Show your sleep quality base on your sleep times.
– Sedentary Remind: You can set a time to remind you up to do some exercise, we suggest you this time could be one hours.
– Quick response: It can download sync software when scan the quick response, if there Is a new version need to update, please contact with our servicer, our company will provide a new link for your download.
– Audio Player: Can play music from local or smart phone after connected with Bluetooth.
– Browser: Browser need your phone has SIM card and surf the Internet.
– You can also haveAlarm/Calendar/Calculator/Profiles/File Manager/Camera/Image viewer/Sounder recorder functions.

NOTICE
– Full charge before use, the charge time need 1-2 hours.
– Bluetooth will disconnect when exceed the distance (up to 10 meters), after switch on the Anti lost, the smart search function can’t be use before reconnect with Bluetooth.

NOTE: The effectiveness of all functions can be affected by the level of battery charge.

5. COMMON TROUBLE SHOOTING
Please refer below key functions for any problems with the watch.

-Unable to switch on: The time of press the power button too short, please keep it more than 3 seconds. Low power, please charge it.
– Shut down automatic: Low Power, please charge the watch.
– Using time too short: Battery Is not full, please make sure it Is full power (full charge need 2 hours at least). During the use of SIM card, the power will be run off soon if the signal too poor.
– Unable to charge: The battery’s life will be reduce after few years, please check if the battery are work. Change a new charger if it Is unworkable. Please check the USB slot connecting good, If no, please try again.
– Not caller’s name when incoming call: Forgot to choose upload the phone book when connected with BT, or unselected keep upload the phone book. Forgot to sync the phone book when reconnected, please pair the device and connect BT again.
– Bad phone call voice: Watch and phone are separated too far, please be more close; Bad signal of BT. Bad signal of your own phone call place, please change a more better place for phone call.

6. MAIN FEATURES
– CPU: MTK6261D, 108 Mhz.
– Mobile phone 2G GSM 850/900/1800/1900
– Capacitive touch screen 1.54” 240*240 Pixs.
– Bluetooth 2.1.
– RAM/ROM:32MB/32MB.
– Support TF card (up to 32 GB)
– 0.08 MPX camera.
– Battery 380 MAh Li-Battery.
– Micro SIM card slot.
– Speaker, microphone, multi languages.
Federal Communications Commission (FCC) Interference Statement

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.

Note: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This mobile device meets guidelines for exposure to radio waves. Your mobile device is a radio transmitter and receiver. It is designed not to exceed the limits for exposure to radio waves recommended by international guidelines.

The SAR limit adopted by USA and Canada is 1.6 watts/kilogram (W/kg) averaged over one gram of tissue. The highest SAR value reported to the Federal Communications Commission (FCC) and the Industry Canada (IC) for this device type when it is tested for use at the mouth is 0.045 W/kg, and that when it is properly worn on the wrist-worn is 1.003 W/kg.

The device complies with the RF specifications when the device is used near your ear or at a distance of 1.0 cm from your mouth. Ensure that the device accessories such as a device case and a device holster are not composed of metal components. Keep your device 0 cm away from your wrist-worn to meet the requirement earlier mentioned.

https://fccid.io/2AI8NDZ09/User-Manual/User-Manual-3092651.pdf

Losoi TWS-K2 Manual

Operational Menual

Wireless Bluetooth Headset TWS-K2

Inside the box
1. Bluetooth Headset x2PCS
2. Charging Case x1PCS
3. Micro USB Cable x1PCS
4. Operations Guide x1PCS

Functional Diagram


Specification

1. Version: BT4.1+EDR
2. Supports: HSP/HFP/A2DP/AVRCP
3. Charging Interface: Point-contact
4. Size: 28*20*28mm
5. Standby Time: About 4Ohours
6 . Call Time: About 2hrs
7. Play Time: About 2hrs
8. Net Weight: 5.Og
9. Charging Case Size: 80*60*30mm
10. Charging Case Weight: 45g

How to Use

– Charging
1. Placed the earphones on the slots of the charging case correctly
2. Connect the charge cable to Micro Jack on the charging case
3. Plug the charge cable to a Charger(3.5V) or USB output of PC
3. Indicator light shows red, when fully charged the blue lights up
4. Charging Case should be charged 2hrs at least

– To Switch the Headset On/Off
1. To turn on: Press and hold the Multi-function key for 4s then the blue lights up
2. To turn off: Press and hold the Multi-function key for 3s then the red lights up while they’re working.

– True Wireless Mode Pairing
1. Press and hold the Multi-function keys for 7 seconds of the two headsets Simultaneous,then they will be paired and connected automatically
2. The headsets will be specified as Left channel and Right channel relatively, then the left headset will enter pairing mode again, enable your phone’s Bluetooth and search, click the model “TWS-K2” to pairing and connect.

-To Pair the Headset Single with Your Phone
a. Press and hold the Multi-function key for 7 seconds, ~e!ease when the red light and blue light flash alternatively, the Bluetooth headset enters pairing state;
b. Open the B!uetooth of your mobile phone and search , click the model “TWS-K2” to pairing.
c. If asked to enter the password, please enter 0000.

-To Answer A Call
Click the Multi-function key of the host headset shortly

-To End A Call
Press the Multi-function key of the host headset shortly while your phone is online.

-To Reject A Call
Press the Multi-function key of the host headset and hold for about 1 seconds while there is a incoming call on your phone.

-To Redial the Last Number
Press and hold the Multi-function key of the host headset.

-To Active Voice Dialing
As long as your phone support for voice dialing, double click Lise Left Multi-furEcLiun key during standby mode for Isecond then the last number you have called will be redial out.

-To Play or Pause
Click the Multi-function Key of host headset to control pause and play the music. To Play Next Song Click the Multi-function Key of vice headset to play the next song.

Safety Precautions

Please read follow and keep these instructions
1. Keep the device out of extreme heat and humid
2. Power time may different depending on personal habits
3.Heed all warnings on the product and in the operation instructions
4.Do not listen at high volume level for long period to protect hearing
5.Stop ushing this product immediately if it causes discomfort or pain.

Kindly Remind: We strongly recommend that you use for the first time a full battery, please!

FCC Warning
This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residental installations. This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to fade communications. However, there is no guarantee that interference will not occur in a panticufar installation. If this equipment does cause harmful interference to radio or televfsfon reception, which can be determined by turning the equipment off and on, the user is encouraged to try to corract the interference by one or more of the folliowing measures:

– Reorient or relocate the receiving antenna
– Increase the separation between the equipment and receiver.
– Conned the equipment into an outlet on a circuit dfferent from that to which the receiver is connected.
– Consult the dealer of an experienced radio/TV technidan for help.

Caution: Any changes or modiifications to this device not explicitly approved
by manufecturer could void your a~thorify to operate this equipment.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions’ (1) This device may not cause harmful interference, and CZ) mis device must accept any interference received including interference that may cause undesired operation.

The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition wfffiout restridion.

https://fccid.io/2AKCVTWS-K2/User-Manual/10-user-manual-3214345.pdf

 

HPlus DFIT Smart Watch User Manual

Smart Watch User Manual

Product Specification
Chip model: nRF51822 ( Cortex M0 16MHz)
Memory: 256K
Acceleration sensor: Three-axis acceleration sensor
Heart rate sensor: Green light static heart rate sensor
Display: OLED 0.66 64×48 Dots
Motor: Cylindrical vibration motor
Key-press: Touch key
Battery: 80mAh

Notice
The wristband contains magnatic component, he who is installed a pacemaker, or have implanted electronic devices, or metal, please do not use it. Please stop using it when any discomfort symptoms happen. If use substandard charging power supply, will shorten the battery life, and even damage the battery.
We reserve the right to modify the User Manual without any notification. It is normal condition if some functions differs from different app versions.
We reserve all the right for the final explanation .

Turn on/off the Wristband
1. Long press the touch key for 4 seconds, users see the Welcome interface. It is touch key, please do not press the key with strong pressure.
2. Short press the key to enter to the Device Management interface with power off icon at the top-left corner. Then long press the touch key to turn off the wristband.
3. Long press to choose the function and short press to switch the functions.

Charging
Charger: voltage 5V, electric current 500MA-1000MA.
Charging time: 30 minutes.

Connect the chrger with wristband as below.

Time

1. Battery power display
2. Date Display
3. Time Display


Heart Rate Interface


1. Heart Icon,long press the icon to start testing with beating.
2. Display the real time heart rate.
Notice :
The heart rate testing data can not be used as medical data.
The time will a little longer for the first timetesting ,it is normal.

The best wearing manner:

1. keep a finger width between the wristband and ulna
2. keep the heart rate sensor clinging to skin

 

 

 

 

Pedometer

1. Pedometer Icon
2.Display the real time steps

Distance Interface

1. Distance icon
2.Display the whole distance according to the pedometer

Calories Display
1. Calories icon
2.Display the real time calories

Palming bright screen

1. long press the touch key to turn on/off the functio

Device Management

1. Turn on/off icon, the wristband can only be turned off in this interface in case of the wrong operation.
2. Battery power icon
3. Bluetooth connection icon, this icon means Connected. this icon means Disconnected.

4:Bluetooth name DFit
5. The last four letters in the MAC address is used for distinguish each wristband. For example as above picture, the Bluetooth name is Dfit EEF2 found by App. 6.Software serial number :V1.80

APP download
Please scan the QR code below to download HPlus Watch APP

Google play
App for foreign Android users
https://play.google.com/store/apps/details?id=com.richtechie.hplus

iOS
App for ios users
https://itunes.apple.com/us/app/hplus-watch/id1021512165?l=zh&ls=1&mt=8

1. Aftet HPlus Watch APP Installation completed,please fill up your information such like Height、weigh、age、gender etc.
2. Wristband connect with APP; Click Bluetooth Device in the System Setup to enter the interface, pull the screen from the top to bottom. Search and find the Bluetooth name, then click and connect wristband. After connection, the date and time on the wristband will be updated automatically.

3.Data graph
After connection, total distance,total steps, total calories, Min heart rate, average heart rate, max

heart rate, yesterday data and data summary will be shown on the ap interface.
4. Real time Heart rate
Start heart rate testing,it can record your heart rate for whole day.
5. Settings
Used to set up all functions on ap.
a. Bluetooth, used to connect wristband Bluetooth
b. Sync, used to sync wristband date
c. Incoming calls, when you turn on the function, the watch rings and vibrate with icon remind.
d. Time reminder: Alarm clock, when you turn on the function, wristband will remind you regularly.
e. Sit notification, when you turn on the function, the watch will remind you to do some exercise.
f. Screen save timer, used to set up the time for screen bright.
g. Erase user data, used to erase the historical data in the wristband.

FCC Caution:
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.

 

https://fccid.io/2AL5W-DFIT/User-Manual/User-Manual-3395108.pdf

 

 

Manufactured by: SHENZHEN ZHIMEIDE TECHNOLOGY CO.,LTD

FCC ID: 2AL5W-DFIT

Huawei WS331c Range Extender User Manual

Huawei WS331c Range Extender User Manual

Quick Start


Step 1: Plug the WS331c into a power socket near the wireless router

How to restore default settings: When the WS331a is powered on, use a needle to press and hold the Reset key for 2 seconds or more until the indicator becomes off. For the full user guide, visit http://consumer.huawei.com/en/.

Step 2: Wirelessly connecting WS331c to the wireless router
Method 1: Automatic Connection through WPS Button

Method 2: Manual Connection through the WS331c Web Page
You can configure the WS331c using a phone, tablet, or laptop. This guide uses a phone as an example.

1. Check the WS331c’s Wi-Fi network name (unencrypted by default), and then wirelessly connect your phone to the Wi-Fi network.

 

 

 

2.
On your phone, open a browser and enter 192.168.3.1 or mediarouter.home to access the WS331a configuration screen. Then enter the login password (default value: admin).

 

 

3. Touch Internet Connection Wizard. Complete the configuration by following the Internet Connection
Wizard.

 

 

 

Safety Information

1. Safety information
This section contains important information about the operation of your device. It also contains information about how to use the device safely. Read this information carefully before using your device.
Electronic device
Do not use your device if using the device is prohibited. Do not use the device if doing so causes danger or interference with other electronic devices.

Interference with medical equipment
– Follow rules and regulations set forth by hospitals and health care facilities. Do not use your device where prohibited.
– Some wireless devices may affect the performance of hearing aids or pacemakers. Consult your service provider for more information.
– Pacemaker manufacturers recommend that a minimum distance of 15 cm be maintained between a device and a pacemaker to prevent potential interference with the pacemaker. If using a pacemaker, hold the device on the side opposite the pacemaker and do not carry the device in your front pocket.

Areas with flammables and explosives
– Do not use the device where flammables or explosives are stored (in a gas station, oil depot, or chemical plant, for example). Using your device in these environments increases the risk of explosion or fire. In addition, follow the instructions indicated in text or symbols.
– Do not store or transport the device in containers with flammable liquids, gases, or explosives.

Operating environment

Avoid dusty, damp, or dirty environments. Avoid magnetic fields. Using the device in these environments may result in circuit malfunctions.
– Keep the device away from electronic appliances that generate strong magnetic or electric fields, such as a microwave oven or refrigerator.
– During thunderstorms, power off your device to protect against lightning strikes.
– Do not use your device during thunderstorms to protect your device against any danger caused by lightning.
– Ideal operating temperatures are 0°C to 40°C. Extreme heat or cold may damage your device or accessories.
– Keep the device and accessories in a well-ventilated and cool area away from direct sunlight.
Do not enclose or cover your device with towels or other objects. Do not place the device in a container with poor heat dissipation, such as a box or bag.
– To protect your device or accessories from fire or electrical shock hazards, avoid rain and moisture.
– Keep the device away from sources of heat and fire, such as a heater, microwave oven, stove, water heater, radiator, or candle.
– Observe local laws and regulations, and respect the privacy and legal rights of others.
– Do not block device openings. Reserve a minimum of 10 cm around the device to dissipate heat.
– Stop using your device or applications for a while if the device is overheated. If skin is exposed to an overheated device for an extended period, low temperature burn symptoms, such as red spots and darker pigmentation, may occur.
– Do not touch the device’s antenna. Otherwise, communication quality may be reduced.
– Do not allow children or pets to bite or suck the device or accessories. Doing so may result in damage or explosion.
– The device should be installed and operated with a minimum distance of 20 cm between the radiator and your body.
– Keep the device in a place with good reception. The distance between the device and other
metal materials (such as metal brackets or metal doors and windows) should be greater than
25 cm and the distance between the device should be greater than 30 cm.

Child’s safety
– Comply with all precautions with regard to child’s safety. Letting children play with the device or its accessories may be dangerous. The device includes detachable parts that may present a choking hazard. Keep away from children.
– The device and its accessories are not intended for use by children. Children should only use the device with adult supervision.

Power adapter safety
– The power plug is intended to serve as a disconnect device.
– For pluggable devices, the socket-outlet shall be installed near the devices and shall be easily accessible.
– Unplug the power adapter from electrical outlets and the device when not in use.
– Do not drop or cause an impact to the power adapter. If it is damaged, take it to an authorized service center for inspection.
– If the power cable is damaged (for example, the cord is exposed or broken), or the plug loosens, stop using it at once. Continued use may lead to electric shocks, short circuits, or fire.
– Do not touch the device or the power adapter with wet hands. Doing so may lead to short circuits, malfunctions, or electric shocks.
– If your power adapter has been exposed to water, other liquids, or excessive moisture, take it to an authorized service center for inspection.

Cleaning and maintenance
– During storage, transportation, and operation of the device, keep it dry and protect it from collision.
– Keep the device and accessories dry. Do not attempt to dry it with an external heat source, such as a microwave oven or hair dryer.
– Do not expose your device or accessories to extreme heat or cold. These environments may interfere with proper function and may lead to fire or explosion.
– Avoid collision, which may lead to device malfunctions, overheating, fire, or explosion.
– If the device is not going to be used for an extended period of time, power it off.
– If anything unusual occurs (for example, if the device emits smoke or any unusual sound or smell), immediately stop using it, power it off and contact an authorized service center.
– Before you clean or maintain the device, stop using it, stop all applications, and disconnect all cables connected to it.
– Do not use any chemical detergent, powder, or other chemical agents (such as alcohol and benzene) to clean the device or accessories. These substances may cause damage to parts or present a fire hazard. Use a clean, soft, and dry cloth to clean the device and accessories.
– Do not place magnetic stripe cards, such as credit cards and phone cards, near the device for extended periods of time. Otherwise the magnetic stripe cards may be damaged.
– Do not dismantle or remanufacture the device and its accessories. This voids the warranty and releases the manufacturer from liability for damage. In case of damage, contact an authorized service center for assistance or repair.

Disposal and recycling information
This symbol (with or without a solid bar) on the device, batteries (if included), and/or the packaging, indicates that the device and its electrical accessories (for example, a headset, adapter, or cable) and batteries should not be disposed of as household garbage. These items should not be disposed of as unsorted municipal waste and should be taken to a certified collection point for recycling or proper disposal.
For more detailed information about device or battery recycling, contact your local city office, household waste disposal service, or retail store.
Disposal of the device and batteries (if included) is subject to WEEE Directive Recast (Directive 2012/19/EU) and Battery Directive (Directive 2006/66/EC). The purpose of separating WEEE and batteries from other waste is to minimize the potential environmental impacts and human
health risk of any hazardous substances that may be present.

Reduction of hazardous substances
This device is compliant with the REACH Regulation [Regulation (EC) No 1907/2006] and RoHS
Directive Recast (Directive 2011/65/EU). Batteries (if included) are compliant with the Battery
Directive (Directive 2006/66/EC). For up-to-date information about REACH and RoHS
compliance, please visit the web site www.huaweidevice.com/certification.

EU regulatory conformance Statement

Hereby, Huawei Technologies Co., Ltd. declares that this device is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. For the declaration of conformity, visit the web site www.huaweidevice.com/certification. The following marking is included in the product:

 

This device may be operated in all member states of the EU. Observe national and local regulations where the device is used. This device may be restricted for use, depending on the local network.

Restrictions in the 2.4 GHz band:
Norway: This subsection does not apply for the geographical area within a radius of 20 km from the centre of Ny-Ålesund.

FCC Regulatory Compliance
FCC statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the  interference by one or more of the following measures:
–Reorient or relocate the receiving antenna.
–Increase the separation between the equipment and receiver.
–Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
–Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Caution: Any changes or modifications to this device not expressly approved by Huawei Technologies Co., Ltd. for compliance could void the user’s authority to operate the equipment. This device is intended to be attached to a receiver that is not used to receive over-the-air broadcast signals. Connection of this device in any other fashion may cause harmful interference to radio communications and is in violation of the FCC Rules, part 15.

2 Legal Notice
Copyright © Huawei Technologies Co., Ltd. 2014. All rights reserved.
THIS DOCUMENT IS FOR INFORMATION PURPOSE ONLY, AND DOES NOT CONSTITUTE ANY KIND OF WARRANTIES.
Privacy Policy
To better understand how we protect your personal information, please see the privacy policy at http://consumer.huawei.com/privacy-policy.

3 For More Help
Please visit www.huaweidevice.com/worldwide/support/hotline for recently updated hotline and email address in your country or region.

https://fccid.io/QIS-WS331C/User-Manual/users-manual-2165578.pdf

AirTies Air 4920 Smart Mesh User Manual

AirTies Air 4920 Smart Mesh User Manual

For more information:
http://www.airties.com/products

Quick Installation Guide

1600 Mbps Smart Mesh Access Point Air 4920
EASY SETUP: ACCESS POINT
1. Position one Air 4920 next to your router and connect the two using the enclosed Ethernet
cable (yellow plug).
2. Connect the Air 4920 device to the mains and press the power switch.
3. Wait until both 5 GHz and 2.4 GHz LEDs are solid green  This may take up to 3 minutes.

4. Now, you can connect mobile devices to your new wireless network.Factory default network name and password are labeled on the bottom of the device.
– On each client (e.g. laptop, phone or tablet),
connect to the network on the label.
– Enter the network password when prompted.

5. (Optional) You can change network name (SSID) and password of your network.
Connect to your network, open the web browser and type “http://air4920.local” to the
address bar. Log in and navigate to QUICK SETUP from the left pane. (Default login password is blank.)

EXTEND YOUR WiFi COVERAGE (MESH):
Preparation: Connecting the new Air 4920
1. In the room in which the router is located, position the new Air 4920 at a distance of around three
meters from the existing Air 4920 device, connect it in to the mains and wait until both 5 GHz and 2.4 GHz LEDs are flashing green ( 4 seconds ON, 4 seconds OFF ). This may take up to 3 minutes.

2. 2.a Press the WPS button on the existing Air 4920 (next to the router) for 2 seconds and
then on the new Air 4920 for 2 seconds (2.b).
The 5 GHz and 2.4 GHz LEDs start to flash and the devices connect automatically. This process may take up to five minutes. The connection has been established once the LEDs light up green (The 5 GHz LED will turn OFF briefly once in every 5 seconds).
Congratulations, you have successfully configured your new device. Your existing Air 4920 network credentials are automatically configured to your new Air 4920.

Note: If the 5GHz LED on the new device does not light up green within five minutes,
please repeat step 2.

Setting up the Air 4920 in the room of your choice
3. The new Air 4920 can now be unplugged and placed in the room of your choice.
The connection will be established automatically. This process will take up to three minutes.
Note: If 5 GHz LED does not light up green (The 5 GHz LED will turn OFF briefly once in every
5 seconds) within three minutes, please consult the chapter «Troubleshooting» (page 5).
4. (Optional) Now, you can connect wired devices (in this example, the Set-Top Box) to the Air 4920 using the ethernet cable (yellow plug).

5. (Optional) You can add additional Air 4920s to your network by repeating steps from 1.
Improving wireless coverage
If you would like to improve wireless coverage in another room, you can set up an additional Air 4920. You can also connect devices via Ethernet to this Air 4920 (for example a STB, computer or game console).

 

Improving range
If the location you want to cover is too far away from your existing Air 4920, you can install additional Air 4920s to reach there.
 

 

TIPS FOR BEST PERFORMANCE:
– Turn off wireless service on your modem.
– Keep units away from:
– Potential sources of electrical interference. Equipment that potentially cause interference include ceiling fans, home security systems, microwaves, PCs, and cordless phones (handset and base).
– Large metal surfaces and objects. Large objects and wide surfaces such as glass, insulated walls, fish tanks, mirrors, brick, and concrete walls can also weaken wireless signals.
– Sources and areas of heat such as ovens and sun rooms as well as direct sun light even if there is good air conditioning.

– Also, it is highly recommended that uninterruptable power supplies (UPSes) (or, at least, surge protectors) are used to protect Air 4920s and other electrical devices (VDSL modems, routers/gateways, set-top boxes, TVs, etc.) from electrical dangers. Electrical storms, voltage surges and other risks associated with the electrical power grid can cause significant damage to electrical devices. In additional, even a 1-second disruption in electrical power is likely to cause all modems, wireless clients, TVs, set-top boxes, etc. to be powered off or to be reset. Even if the equipment starts up automatically, it will be several minutes before all systems come back online and allow you to enjoy your Internet-based services.

TROUBLESHOOTING:

 

NOTES:
– Returning to factory settings:
To return unit to factory settings, press down on the reset button (in a small opening on the back) for 10 seconds. A metal paperclip (with an extended tip) or strong toothpick are typically good choices for this task. When the reset process is triggered, the LEDs in the front will temporarily “shimmer” and the unit will reboot (in about 3 minutes) to factory settings.

 

– If you personalize the network settings, please record them here:
Network Name: ………………………………………………………………
Network Password: …………………………………………………………
User Interface Password: ………………………………………………..

This product makes use of software developed by the open source community. Any such software is licensed under the specific license terms applicable to that particular software (like GPL, LGPL etc). Detailed information on the applicable licenses and license terms can be found on the device’s user interface. By using this product, you acknowledge that you have reviewed such license terms and that you agree to be bound by them. Where such terms entitle you to the source code of said software, that source code will be made available at cost upon request from AirTies. To obtain a copy of said source code, please send your request in writing via email to [email protected] or via snail mail to: AirTies Wireless Communications  Gulbahar Mah. Avni Dilligil Sok. No:5 Celik Is Merkezi, Mecidiyeköy, 34394 ISTANBUL/Turkey AirTies will mail to you a CD with the requested source code for $9,99 plus the cost of shipping. For details please contact [email protected]

https://fccid.io/Z3WAIR4920/User-Manual/User-Manual-2554906.pdf

LKGPS LK209 GPS Tracker User Manual

Power magnetic GPS Tracker Manual


Preface
LK209

Thank you for purchasing the tracker. This manual shows how to operate the device smoothly and correctly.Make sure to read this manual carefully before using this product. Please note that specification and information are subject to changes without prior notice in this manual. Any change will be integrated in the latest release. The manufacturer assumes no responsibility for any errors or omissions in this document.

FCC RF Exposure Information and Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

FCC Warning
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

NOTE 1: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.

NOTE 2: Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
1. Summary
Working Based on existing GSM/GPRS network and GPS satellites, this product can locate and monitor any
remote targets by SMS or internet. The most advanced technology of GPS and AGPS dual positioning.
2. Applications
1. Vehicle rental / Fleet management etc
2.Container/cargo/asset tracking
3.Hardware Description

4. Content Specs.

5.Userage:
5.1 SIM card installation
1.Open the rubber plug
2.Insert the GSM SIM card.
3.close the rubber plug.
5.2 Battery and Charger
Do charge the battery to capacity in 8 -12 hours for first time. Please use the battery and charger provided bythe manufacturer. This unit adopts built-in Li-ion battery, and full battery can standby 120days. After first use, the battery usually should be charged fully in 5–8 hours.
Cautions:
a: For it’s Li-ion battery, which contains harmful chemicals and may burst, please don’t bump, puncture it violently and keep it off fire.
b: Please charge the battery in time to keep it working normally.
5.3 Startup
– Put the SIM card and battery in place.
– Turn on the unit outdoors by Pushing the button to“On”the indicator is on.
– Set admin number,APN , IP and open GPRS
Eg: Step1.admin123456+space+your phone number
Step2.apn123456+ space+local apn content
Step3.adminip123456+space+101.1.16.228+space+7700
Step4. gprs123456
– In 10 or 40 seconds, the unit will begin to work and acquire the GSM signals as well as the GPS signals. The indicator will keep flashing every 3 seconds when the unit has received the signals.
– When this unit receives GPS signals normally, you can use it and do any setting as the instructions of this manual.

1.Google link: click link, there is map when positioning ok,
no map means no positioning.
2.V:A GPS signal ok.V:V no GPS signal
3.2013-08-30 20:54:15: the last time receive GPS signal.
4.Spd:000km/h: the speed of tracker ran.
5.Bat:6 battery balance(the range is from 1 to 9)
6.ID:4102000759: ID code of device(used for connect
tracking website or APP)
7.S19G04;plmn:46001 GSM operator data
8.Lac:9516,cellid:23596 LBS data

5.4Change the password
5.4.1 Set Password: Send sms: “password+old password+space+new password” to the unit to change the password.Status of indicator Meaning Red led on all the time Charging red led off Full battery or charged full For Example, pls send sms: “ password123456 000000” to terminal device, it will reply sms: “password OK”. New password 000000 changed in success.

5.4.2 Be sure keep the new password in mind, you have to upload the software to restore the original setting in case of losing the new password.
5.4.3 Make sure the new password is in 6 digits Arabic numbers, or the tracker can not recognize the password.
5.4.4 Make sure that all the symbol“+”in sms commends is just for quick understanding, which don’t need to enter “+” in sms, and “space” means press the spacebar button of the cell phone.

5.5Authorization
5.5.1 Send SMS:“ admin+password+space+cell phone number” to set up a authorized number. The other authorized numbers should be set by the first authorized number. If the number is successfully authorized, the unit will reply “admin ok!” in SMS.
5.5.2 Send SMS:“ noadmin+password+space+authorized number” to delete the authorized number.
5.5.5 When the authorized number call the device, it will hang up your phone and reply a realtime latitude and longitude information, as below:

5.6Single Locating
5.6.1 If there is no authorized number, when any number dials up the unit, it will report a Geoinfo; If there is already an authorized number, then it will not respond when an unauthorized
number calls it up.
5.6.2 Single message inquires the latitude and longitude information, any telephone number can send instruction “where” to the equipment, then the equipment will reply the latitude and longitude informati on to this telephone.
5.6.3 When an authorized number dials up the unit, it will hang up and report a real-time Geoinfo as below:
*Tracking location, When GPS signals is weak, the position of latitude and longitude included in the SMS is the position that the tracker received GPS signals at last. If it is different with its exact current location, pay attention to check the time included in the SMS you got.
5.7Auto Track
5.7.1 Send SMS command “t030s005n+password” to the tracker device, it will report the “no reply” at 30s intervals for 5 times. (s:second, m:minute, h:hour). This command setting must be
in 3 digits and the maximum value is 255.

5.7.2 Unlimited times auto track: Send SMS “t030s***n+password” to the tracker device, it will reply the “no reply” continuously at 30 seconds intervals.

5.7.3 Cancellation: Send SMS “notn+password” to the tracker device, it will report the “notn ok”.
Note: the interval must not less than 20s.

5.8 Monitor (Voice Surveillance)
5.8.1 The command to switch between Track and Monitor are “tracker” and “ monitor”.
5.8.2 The default mode is “track” (Track mode).
5.8.3 Send SMS “monitor+password” to the unit, and it will reply “monitor ok!” and switch to “monitor” mode.
5.8.4 Send SMS “tracker+password” to the unit, it will reply “tracker ok!” and restore to “track” mode.

5.9Geo-fence
Set up a geo-fence for the unit to restrict its movements within a district. The unit will send the message to the authorized numbers when it breaches the district.
5.9.1 Set up: When the unit stays immobile in a place for 3-10 minutes, the user can Send SMS: “stockade+password+space+latitude,longitude; latitude,longitude” to unit to set the restricted district.
Remark: The first latitude&longitude is coordinate of the top left corner of the Geo-fence, while the second latitude&longitude is the coordinate of the bottom right corner.
5.9.2 Cancel: Send SMS:” nostockade+password” to deactivate this function,tracker will reply “nostockade ok”

5.10Movement alert
5.10.1 Set up: When the unit stays immobile in a place for 3-10 minutes, the user can send SMS: “move+password” to the unit, then the unit will reply “move ok!”. In case of such a movement
(the unit default distance is 500M), it will send SMS “Move ALARM+ Latitude and longitude” to the authorized number
5.10.2 Cancel: Send SMS:” nomove+password” to deactivate the movement alert, tracker will reply “nomove ok”.

5.11 Overspeed alert:
5.11.1 Set up: Send SMS: “speed+password+space+080” to the unit (suppose the speed is
80km/h), and it will reply “speed ok!”. When the target moves exceeding 80 km/h, the unit will
send SMS :”speed ALARM !+ Latitude and longitude” to the authorized numbers every 5
minutes.
5.11.2 Cancel: Send SMS “nospeed+password” to deactivate the overspeed alarm, tracker will reply “nospeed ok”.
Remark: The recommended speed should be not less than 50km/h. For below that rate, it will be
effected the accuracy by gps signals drift etc.

5.12Low battery alert
When GPS device battery is going to be about 3.7V, it will send SMS: “bat:l” at 30 minutes interval.

5.13Terminal (local) Time Setting
Send SMS “time+space+zone+password+space+local time”.
For example, Send SMS “time zone123456 8” (time zone of China).
If the local time zone is negative as “-3”, then it should set as SMS: “time zone123456 -3”.


5.14Sleeping power-save mode

On normal status, when the unit stoped over 10minutes, it will change to sleeping mode, on this mode, the power consumption is 4mah/h only. When it get any command or been moved, it will start GPS locating automatically. Forced sleeping mode, Setting: Send SMS “sleep+password”, the unit will reply “sleep ok”, it enter to forced sleeping power-save mode. Start device, send SMS “nosleep+password”,the unit will reply “nosleep ok”, it start GPRS


5.17 Shock alert

Note: It is effective sending by authorized number
Send SMS command“shock+password”, the unit will reply “shock ok.”
Cancel: Send SMS command “noshock+password”, the unit will reply “noshock ok.”

5.15Restore factory settings
Note: It is effective sending by authorized number Send SMS command “format”, the unit will reply “The tracher will immediateiy restore the factory settings.All previous settings will be canceled.”

or
Send “begin+password” in SMS to the unit, it will reply “begin ok” and initialize all the settings. (Default password: 123456) For example, send SMS“ begin123456” to the tracker via a cell phone, If succeeded, it will reply“begin ok”.

5.16 GPRS setting
User must send SMS via cell phone to set up IP, port and APN before starting GPRS.

5.16.1 Setting up APN
5.16.1.1 APN standards for Access Point Name and differs from country to country. For more
information about the local APN, inquire with your local GPRS network operator.
5.16.1.2 Text the tracker a SMS “apn+password + Space + your local APN” via a cell phone
and if succeeded in setup, the tracker will return the message “apn ok”.
5.16.1.3 e.g. send SMS command “apn123456 cmnet”. If succeeded, “apn ok” is returned by
the tracker in SMS.
Notes: 123456 refer to password of tracker and CMNET is the APN of China Mobile (One of
GSM Operator in china).
5.16.1.4 Set IP Send SMS command:adminip123456 101.1.16.228 7700 If succeeded,
“adminip ok”

5.16.1.5 Dropped Alarm
When device have been attached on metal 15 sec after ( the Dropped button have been pressed 15 sec ) ,if it device was dropped , it would alarm to the admin number by SMS or calling .

6.command list(pls note 123456 is the default password) .

7. Web platform and sever ip&port
Website Sever IP Port
www.lkgps.net 101.1.16.228 7700

8.App download
8.1 android version: scan below QR code

8.2 ios version: search “LKGPS” in app store


9. Faults & The solutions

https://fccid.io/2AI9PLK209/User-Manual/Users-Manual-3082858.pdf

Hitron CODA-4582 / 4682 / 4782 Manual

Hitron CODA-4582 / 4682 / 4782 Manual

QUICK START GUIDE


1. Connect t o t he net work
2.Set up your wireless net work

Check the Box Contents

STEP 1: Look in the box and make sure you have the following:


The Hit ron CODA-4582/ 4682/ 4782 is an application gateway that provides wired and wirel ess high-speed Int ernet access as well as optional MoCA (Multimedia over CoaxAlliance) net working to the Ethernet -enabled devices in your home f or a fast and easy home entert ainment network.

Connect to a Cable Outlet

STEP 2: Use a coaxial cabl e (not included) to connect the device’s CABLE connect or to a cable outlet.

Connect to a Power Outlet

STEP 3: Use t he power cord provided t o connect t he POWER port to a power outlet.

Connect to an Ethernet -Equipped Device (Optional)

STEP 4: Use the Ethernet cable provided to connect one of the LAN ports to an Ethernet -equipped device.

User Configurat ion (Optional)

STEP 5: In a web browser, enter 192.168.0.1 in the address bar followed by Username and Password, as below.

Connect wit h Wireless Devices (Optional)

STEP 6: Connect your wirel ess devices wit h t he correct SSID and Passphrase. If you have not changed them, the default values are indicated on the sticker on the back of the unit.
Connect your wirel ess devices wit h t he WiFi Prot ected Setup (WPS). Access the configuration interface (seestep 5), enter the Wireless page to enable WPS and set Encrypt Mode to AES, then press Save Changes. Press this button to begin the WPS Push-Button Configuration (PBC) procedure. Press the PBC button on your wireless clients in the coverage area within two minutes to enable them to join the wireless network.

Setup Complete

STEP 7:Congratulations! You have successfully setup your CODA-4582/4682/4782. If you have any problems, see the section below for help in identifying the cause.

IP Addresses

If the CODA-4582 is successf ully connected to the network (see LED Display) but you cannot access the Int ernet from a connected computer, your computer’s IP Address may be setup improperly. In your computer’s network settings, ensure that it is configured to either receive an IP address automatically (recommended) or that it has a static IP address in the 192.168.0.10~192.168.0.254 range. For more information, consult your operating system’s Help documentation.

LED Display

Safet y Warnings

Warning
Rsk or electrical SOCK·Do not expose the device to water or mosture The device is a hign-performance communications device designed for home and ottice environments. Do not use tne device outdoors. Keep the device In an environment between O CN 40 C (32 F 104°F). To avold overheating, do NOT place any Object on top or the device. Do not restrict the ↑low of alr around the cable modem. The manufacturer assumes no llablitiestor damage caused by any improper use of the device
DISCLAIMER
The manufacturer assumes no llabllties with respect to the contents of this document. The manufacturer als0 reserves the right to revise this document or update the content thereor without any obllgation to notity any person of such revis ons or amendments Specificaions subject to change without notice
CAUTION
The cable distribution system should be grounded (earthed) in a accordance with ANS NEPA 70, the Nationa日ectrical Oode (NEC. In particular Section 820.93, rounding ol Outer Oonductive snleid Coaxial Cable .

FCC Statement
Federal Communlcatlon Commlsslon Interference Statement
This equlpment has been teted and found to comply with the limitsfor a Ciass B dlgltal device, pursuant to Part 15 of the FOC Fules These llmits are des gned to provide reasonable protection agalnst harmful Interference In a resdential Instalation. This equipment generates, uses and can radlate radlo trequency energy and, t not Installed and used In accordance with the Instructions, may cause harmfu Interference to radio communlcations.
However, there is no guarantee that Interference wll not occur in a particular Installation. If this equipment does cause harmful Interterence to radlo or televsion receptlon, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the Interference by one of the following measures

1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
4. Consult the dealer or an experienced radio/TV technician for help.

FOC Caution: Any changes or modifications not express y approved by the party respons ble for compliance could vold the user’s autnority to operate thls equipment

This device is going to be operated in 5.15-5.25GHz frequency range, Isrestricted In Indoor environment only.

This device complles with Part 15 of the FOC Rules Operation is subject to the following two conditions (1) This device may not cause harmful interterence, and (2) this device mus accept any Interterence recelved, Including Interterence that may cause undesred operation. For product aval lable in the USA Canada market, only channel 1~11 can be operated·Selection or other channels is not possible This device and it’s antennas s must not be co-located or operating In conjunction with any other antenna or transmltter except In accordance with FoC muit-transmitter product procedures.

IMPORTANT NOTE:
FCC Radlatlon Exposure Statement:
This equipment comples with FOC radiation exposure imits sat ↑orth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 21cm between the radiator & your body.
IC Statement:
This device compl es with ndust ry Canada license exempt RBI st andard s er ation s sub ect t o t he ↑ | owi ng t wo conditions: 1 this de ce may not cause Interte ence, and 2) thi S de ce must accept any int ert erence including Int ert erence t hat may cause undesred operation of the device.

Le présent apparev est conforme aux CNR dindustrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditons suivantes: (1) lapparei ne doit pas produire de broumlage, etde lappareil doit accepter tout brouilage radioślectrique subi, même sile broulage est susceptible den compromettre le fonctionnement.

For product avalable in the USA Canada market, only channel 1 11 can be operated. Selection ot other channels is not possible.

Pour les produits disponibles aux Etats-Unis/ Canada du marché, seul le canal 1 à 11 peuvent être expbités. Sélection d’autres canaux n’est pas possible.

This device and it’s antennass) must not be co-located or operat ing in conjunction with any other antenna or transmitter except In accordance with i multi-transmitter product procedures.

Cet apparei et son antene (s) ne doit pas être co-locaisés ou fonctionnement en association avec une autre antenne ou transmetteur.

The device for the band 5150-5250 MHz is only for Indoor usage to reduce potential for harmful Interference to co-channel mobilesatelte systems.

Les dispositifs fanctionnant dans la bande 5150-5250 MHz sont réservés uniquement pour une utilisation à ntérieur afin de réouire les risques de brouilage préjdiciable aux systèmes de satlites mobies tiisant les mêmes canaux.

IC Radlatlon Exposure Statement:
This e uipment compiles with CRSS102 radiation exposure imits sat ↑orth for an uncontrolled en ronment. This equipment should be installed and operated with minimum distance 21cm between the radiator & your body Cet équipement est conforme aux limites dexposiion aux rayonnements IC établies pour un environnement non contrôlé. Cet équioement doit être installé et utilisé avec un minwmum de 21 am de distance entre la source de rayonnement et votre corps.

COPYRIGHT © 2016 HITRON TECHNOLOGIES, INC.

 

https://fccid.io/2AHKM-CODA4782/User-Manual/Users-Manual-3186268.pdf

Bluetooth Mini Earbud S530 Manual

Wireless Mini Earbud Instruction Manual Model: S530


Introduction
This manual will help you operate the wireless speaker. You should first familiarize yourself with the Bluetooth functionality of your cell phone or other devices before using the wireless speaker.

Safty Rules
1. Please follow the rules depicted in this manual colsely to ensure your safty. Before using this wireless speaker, we would strongly encourage you to read through this user manual.
2. Be wary of any edges, uneven surfaces, metal parts, accessories and its packing so as to prevent any possible injury or damage.
3. Do not modify, repair of dismantle this wireless speaker. Doing so may result in fires, electric shocks, complete breakdown of this wireless speaker, etc. All of which, are not covered under warranty.
4. Do not use the wireless speaker in a hazardous location.


Back

Pairing to cell phone or other device
To use your Bluetooth Earphone, you must first pair your earphone with a phone or a computer. Once your earphone is paired to a specific cell phone, they will remain paired and automatically recognize each other whenever they are within range.
Pairing to a phone and entertainment:
– Turn on your phone and ensure its Bluetooth function is activated
– Turn on the earphone and go to the pairing mode
– Search your Bluetooth devices on your phone by following the phone’s user manual for more information.
– After a few second the phone will list the “S530” as a discover device.
– Select it and follow your phone instruction to select this pairing.
– Your phone will confirm the pairing, and then press Yes/OK
– Finally, select to connect with the earphone from your phone.

Charge your Earphone
Connect the earphone to USB Charger with the cable included. Red color LED indicator is ON when charge. The red color LED indicator turns blue when full charged. Make sure that your earphone is fully charged for at least 3 hours before initial use.


Warning:
You must select a qualified charger from a regular Manufacturer. You must charge the earphone if it has been not used for more than 1 month.

Product Specification

FCC Caution
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:

-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.

The device has been evaluated to meet general RF exposure  requirement. The device can be used in portable exposure condition without restriction.


https://fccid.io/2AHU7S530/User-Manual/User-manual-3364526.pdf

Arris BGW210-700 Broadband Gateway User Manual and Admin Help

BGW210-700 Broadband Gateway Release 1.0

Install and Operations Guide
365-095-30882 Revision 4.0
November 2016
ARRIS Copyrights and Trademarks

ARRIS Copyrights and Trademarks

© 2016 ARRIS Enterprises LLC. All Rights Reserved.No part of this publication may be reproduced in any form or by any means or used to  make any derivative work (such as translation, transformation, or  adaptation) without written permission from ARRIS Enterprises LLC. (“ARRIS”). ARRIS reserves the right to revise this publication and to make  changes in content from time to time without obligation on the part of  ARRIS to provide notification of such revision or change.

ARRIS and the ARRIS logo are all trademarks of ARRIS Enterprises LLC. Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks or the names of their products.  ARRIS disclaims proprietary interest in the marks and names of others.

ARRIS provides this guide without warranty of any kind, implied or  expressed, including, but not limited to, the implied warranties of  merchantability and fitness for a particular purpose. ARRIS may make  improvements or changes in the product(s) described in this manual at any time.

The capabilities, system requirements and/or compatibility with third-party products described herein are subject to change without notice.

Tables of Contents

1. ARRIS BGW210-700 Broadband Gateway Introductio…………….. 5
About ARRIS Documentation ……………………………………………………………… 5
Documentation Hyperlinks …………………………………………………………………… 5
Related Documentation………………………………………………………………………….. 6
Document Organization …………………………………………………………………………. 6
2. Preliminary Safety Instructions ……………………………………………………….. 7
Power Supply Installation ……………………………………………………………………….. 7
Telecommunication Installation ……………………………………………………………. 8
Product Ventilation ……………………………………………………………………………………. 8
3. Hardware Gateway Installation …………………………………………………………. 9
Connecting the Power Adapter …………………………………………………………….. 11
Connecting Computers to the BGW210-700 Broadband Gatway…………… 11
Connecting Devices Using Wired Ethernet ……………………………………………………… 11
Connecting Devices Using Wi-Fi ………………………………………………………………………….. 12
Connecting the BGW210-700 Broadband Gateway to the Internet………… 13
Connecting VoIP Telephones ………………………………………………………………………………… 14
4. Basic Troubleshooting …………………………………………………………………………………………. 16
Status Indicator Lights ……………………………………………………………………………………………… 17
Problem Isolation ………………………………………………………………………………………………………… 21
Rear Panel Connectors ………………………………………………………………………………………. 23
Factory Reset Switch …………………………………………………………………………………………. 24
5. Technical Specifications and Safety Information ……………………………………………. 25
Dimensions and Interfaces …………………………………………………………………………………. 25
Power Supply ……………………………………………………………………………………………………. 26
Environment …………………………………………………………………………………………………….. 26
Agency Approvals ……………………………………………………………………………………………… 26
North America …………………………………………………………………………………………… 26
Caring for the Environment by Recycling ……………………………………………………………… 26
6. Important Safety Instructions …………………………………………………………………….. 27
WARNINGS ……………………………………………………………………………………………………….. 27
Product Ventilation ……………………………………………………………………………………………. 27
Telecommunication Installation Cautions …………………………………………………………….. 27
Electrical Safety Advisory……………………………………………………………………………………. 28
Declaration of Conformance ………………………………………………………………………………. 28

47 CFR Part 68 Information ………………………………………………………………………… 28
FCC Caution ………………………………………………………………………………………………………. 29
Radiation Exposure Statement ……………………………………………………………………………. 29
Service Requirements ………………………………………………………………………………………… 30
7. ARRIS Contacts ………………………………………………………………………………………… 31

ARRIS BGW210-700 Broadband Gateway Introduction

The BGW210-700 Broadband Gateway hardware platform can host different software. The Advanced Residential Gateway supports VoIP, IPv6, video delivery, security firewall, and extensive remote management features.
The BGW210-700 Broadband Gateway delivers robust video, primary line telephony, and high-speed data over broadband networks via high-speed Internet connectivity. The four Gigabit Ethernet ports can be separated into different services allowing the configuration of dedicated ports for data. It is designed for advanced DSL network service deployments and supports Quality of Service (QoS) enabled features including:
1. Simultaneous use of phone, video, and high-speed data over any one of the available WAN interfaces
2. IPTV video
3. Concurrent Wi-Fi support for 3×3 802.11n on 2.4GHz, and 4×4 802.11ac on 5GHz
4. Primary line VoIP telephone service

About ARRIS Documentation

This guide presents basic operational concepts, and provides step-by-step instructions for the hardware installation and basic troubleshooting of the ARRIS BGW210-700 Broadband Gateway.

Note: For the purposes of this manual the ARRIS BGW210-700 Broadband Gateway may also be referred to simply as the gateway.

Documentation hyperlink

The hyperlink resides in the page number that follows the title. For example, to access Hardware Gateway Installation in the hyperlink below, hover the mouse over the page number in parenthesis until the finger pointer appears, and then click.

Related Documentation

BGW210-700 Broadband Gateway reference documentation is as follows:
1. BGW210-700 Broadband Gateway Install and Operations Guide (this document)
2. BGW210-700 Broadband Gateway AT&T Software Administrator’s Handbook
3. ARRIS ENB-17244 (select BGW210-700 Hardware Diagnostics Information)

Documents Organization

This hardware install and operation guide consists of six product information chapters presented as follows:
1. ARRIS BGW210-700 Broadband Gateway Introduction (page 5) — Describes the ARRIS® document suite, purpose, and structure of this guide.
2. Preliminary Safety Instructions (page 7) — Provides power supply, telecommunication, and ventilation safety instructions.
3. Hardware Gateway Installation (page 9) — Provides the rear panel illustration, a cabling overview, and procedures to perform BGW210-700 Broadband Gateway connections for the power adapter, wired Ethernet, wireless devices, Internet, and VoIP telephones.
4. Basic Troubleshooting (page 16) — Provides simple suggestions for troubleshooting problems with the initial configuration of the gateway.
5. Technical Specifications (page 25) — Presents system and device specifications and important compliance and safety statements.
6. Important Safety Instructions (page 27) — Provides product, telecommunication, and electrical cautionary information, as well as conformance, radiation, and gateway disposable information

Preliminary Safety Instruction

Warning: Do not use before reading these instructions.
Do not connect the Ethernet ports to a carrier or carriage service provider’s telecommunications network or facility unless:
1. You have the written consent of the network or facility manager, or
2. The connection is in accordance with a connection permit or connection rules.
Connection of the Ethernet ports may cause a hazard or damage to the telecommunication network or facility, or persons, with consequential liability for substantial compensation.

Power Supply Installations

Connect the power supply cord to the power jack on the BGW210-700 Broadband Gateway. Plug the power supply into an appropriate electrical outlet.
Warning: The power supply must be connected to a mains outlet with a protective earth connection. Do not defeat the protective earth connection.
Warning: Use only the power supply and cord that came with the BGW210-700 Broadband Gateway. Failure to use the authorized power supply and cord may cause electric shock, fire, bodily injury, and/or property damage. If the power supply or cord becomes damaged or needs to be replaced, to obtain an authorized replacement please contact AT&T customer service by phone (1.800.288.2020) or via website (www.att.com/support).
Caution: Depending on the power supply provided with the product, either the direct plug-in power supply blades, power supply cord plug or the appliance coupler serves as the mains power disconnect. It is important that the direct plug-in power supply, socket-outlet or appliance coupler be located so it is readily accessible.

Tele Communication Installations

When using telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and injury, including the following:
1. This device is intended for indoor use only.
Warning: Do not install this gateway outdoors.
Warning: Installing and operating this gateway outdoors is a violation of FCC rules.
2. Do not use this product near water, for example, near a bathtub, washbowl, and kitchen sink or laundry tub, in a wet basement or near a swimming pool.
3. Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electrical shock from lightning.
4. Do not use the telephone to report a gas leak in the vicinity of the leak.
Caution: The external phone should be UL listed, and the connections should be made in accordance with Article 800 of the National Electric Code (NEC).
Caution: To reduce the risk of fire, use only No. 26 AWG or larger telecommunication line Cord.

Product Ventilation

The BGW210-700 Broadband Gateway is intended for use in a consumer’s home. Position the device in an upright vertical position located where ambient temperatures remain within a range of 32°- 107°F (0°- 41.7°C). The BGW210-700 Broadband Gateway should not be used in locations exposed to outside heat radiation or where it is subject to trapping of its own heat. The product should have at least two inches of clearance on all sides except the bottom when properly installed and should not be placed inside tightly enclosed spaces unless proper ventilation is provided.
SAVE THESE INSTRUCTIONS

Hardware Getway Installations

A BGW210-700 Broadband Gateway cabling overview, as well as rear panel illustration, is provided below. Also provided are procedures to perform BGW210-700 Broadband Gateway connections for the power adapter, wired Ethernet, wireless devices, Internet, and VoIP telephones.
The following diagram illustrates BGW210-700 Broadband Gateway connections to the Internet using DSL Broadband. Phone and power adapter connections are also illustrated.
BGW210-700 Broadband Gateway Cabling Overview

Alternatively, you can connect the BGW210-700 Broadband Gateway to the Internet using the WAN Ethernet port labeled ONT. See Connecting the BGW210-700 Broadband Gateway to the Internet (page 13) for the detailed procedures regarding this setup.
BGW210-700 Broadband Gateway Rear Panel

Connecting The Power Addapter

The power adapter supplies power to the BGW210-700 Broadband Gateway.
1. Connect the appropriate end of the power adapter cable to the BGW210-700 Broadband Gateway rear panel POWER port.
2. Connect the power plug end to the electrical outlet.
After the BGW210-700 Broadband Gateway is powered on, the power light blinks green momentarily and then remains steady green.
For all power light indications, see Status Indicator Lights (page 17) under Basic Troubleshooting.
Warning: Use only the power supply and cord that came with the BGW210-700 Broadband Gateway. Failure to use the authorized power supply and cord may cause electric shock, fire, bodily injury, and/or property damage. If the power supply or cord becomes damaged or needs to be replaced, to obtain an authorized replacement please contact AT&T customer service by phone (1.800.288.2020) or via website (www.att.com/support).

Connecting Computer to The BGW210-700 Broadband Gateway

The first computer you connect can be used to configure the BGW210-700 Broadband Gateway settings. You can connect more computers and other devices to the BGW210-700 Broadband Gateway using wireless or wired Ethernet.

Connected Device Using wired Ethernet

The BGW210-700 Broadband Gateway has four wired Ethernet ports that can be used to connect computers or other devices.
As shown in the illustration below, to connect a computer to the BGW210-700 Broadband Gateway:
1. Connect one end of the Ethernet cable to one of the Ethernet ports on the BGW210-700 Broadband Gateway.
2. Connect the other end of the cable to the Ethernet port on the computer.
Connecting a Computer to a Ethernet Port of the BGW210-700 Broadband Gateway


After the gateway recognizes the computer, the Ethernet light turns steady green and blinks when the computer starts transferring data with the gateway. See Status Indicator Lights (page 17) under Basic Troubleshooting for all Ethernet light indications.

Connecting Device Using Wi-Fi

The BGW210-700 Broadband Gateway has an integrated Wi-Fi access point to which you can use to connect Wi-Fi devices. By default, the BGW210-700 Broadband Gateway is configured with a Wi-Fi network name (SSID) and is WPA-PSK/WPA2-PSK security enabled.
To connect a Wi-Fi device:
1. On the Wi-Fi device, view the available Wi-Fi networks. The specifics of how you do this depend on the device to which you are connecting.
2.The default Wi-Fi network name (SSID) and the Wi-Fi password (e.g., encryption key) are printed on the label on the side of the BGW210-700 Broadband Gateway.
3. Select the appropriate Wi-Fi network name and connect.
BGW210-700 Broadband Gateway Label

4. At the prompt, enter the Wi-Fi password.
To simplify Wi-Fi device connection to the BGW210-700 Broadband Gateway:
You can configure Wi-Fi Protected Setup (WPS) to the network using the PIN or PUSH method.
For more information about the PIN method, please see the BGW210-700 Broadband Gateway AT&T Software Administrator’s Handbook, as it describes Web UI access for this input.
5. The PUSH method establishes Wi-Fi connectivity if you push the WPS button on the front panel of the BGW210-700 Broadband Gateway and on the Wi-Fi device.
Upon WPS button push, the WPS button light flashes green until WPS is completed successfully, at which point it will stay green for 5-minutes (unless pushed again).
See Status Indicator Lights (page 17) under Basic Troubleshooting for all WPS indications.

Connecting The BGW210-700 Broadband Gateway to the Internet

Note: The appropriate port to connect to the Internet is based on the service configuration from AT&T. Do not change the port used unless instructed to do so. Only one of these wiring arrangements can be used at the same time and attempting to use both may interfere with your service.
The DSL Broadband port (labeled Broadband) can be used to connect the BGW210-700 Broadband Gateway to the Internet:
1. Connect one end of the DSL cable to the green DSL port on the BGW210-700 Broadband Gateway.
2. Connect the other end of the DSL cable to the wall outlet.
After the BGW210-700 Broadband Gateway recognizes the connection, the Broadband light blinks green for a moment and then turns steady green. See Status Indicator Lights (page 17) under Basic Troubleshooting for all Broadband light indications.
BGW210-700 Broadband Gateway Connection to the Internet

Alternatively, you can connect the BGW210-700 Broadband Gateway to the Internet using the WAN Ethernet port (labeled ONT):
1. Connect one end of an Ethernet cable to the WAN Ethernet port on the BGW210-700 Broadband Gateway.
2. Connect the other end of the cable to the operator provided WAN Ethernet jack or ONT.
After the BGW210-700 Broadband Gateway recognizes the connection, the Broadband light blinks green for a moment and then turns steady green. See Status Indicator Lights (page 17) under Basic Troubleshooting for all Broadband light indications.

Connecting VOIP Telephones

The BGW210-700 Broadband Gateway includes one RJ-14 port (labeled Phone 1 & 2) with the capacity to support two phone lines using a splitter or multi-jack adapter.
Note: The BGW210-700 Broadband Gateway supports two VoIP lines over one RJ14 (FXS) VoIP port. To connect two phone lines, an inner and outer pair splitter adapter must be attached to the RJ14 (FXS) VoIP port to terminate both lines.
Warning: Do not connect the VoIP lines to your current home telephone wiring, especially if your home has an alarm system. Ensure that you are subscribed to VoIP service for this interface to be used.
As shown in the figures below, to connect phones directly to your gateway:
1. Connect one end of the phone cable to the gray Phone Lines 1&2 connector on the BGW210-700 Broadband Gateway.
2. To connect to the telephone(s), do one of the following:
3. For one phone, connect the phone cable directly to the telephone.
Single Phone Connection

For two phones, connect the phone cable to a splitter and then to the phones.
Two Phone Connection Using Splitter

Note: To prevent interference with cordless phones, ensure that the BGW210-700 Broadband Gateway is at least 5 feet (1.5 m) from any cordless phone base station.
After the gateway recognizes the phones (Line 1 and Line 2), the Phone 1 & Phone 2 lights turn steady green and blink when the associated phone is in use. See Status Indicator Lights (page 17) under Basic Troubleshooting for all Phone light indications.

Basic Troubleshooting

This chapter provides simple troubleshooting suggestions for issues with the initial configuration of the BGW210-700 Broadband Gateway. The following topics are covered:
 Status Indicator Lights (page 17)
 Rear Panel Connectors (page 23)
 Factory Reset Switch (page 24)
Before troubleshooting:
 Read this guide, including Hardware Gateway Installation (page 9) and all of the subtopics.
 Set the TCP/IP controls on the PC to obtain an IP address automatically.
 For additional troubleshooting support please see BGW210-700 Broadband Gateway AT&T Software Administrator’s Handbook, which addresses product Web UI and CLI information.

Status Indicator lights

Check the status indicator lights (LEDs) to begin troubleshooting. Use the front and rear view graphics that follow, as well as the LED Activity descriptions table to interpret the LED indicators.
BGW210-700 Broadband Gateway Status Indicator Lights
Front View


Rear View

Rear Panel Connectors

Connectors on the rear panel are depicted below.
BGW210-700 Broadband Gateway Rear Panel


Note: The BGW210-700 Broadband Gateway supports two VoIP lines over one RJ14 (FXS) VoIP port. To connect two phone lines, an inner and outer pair splitter adapter must be attached to the RJ14 (FXS) VoIP port to terminate both lines.

Factory Reset Switch

The Reset switch will result in a reboot of the BGW210-700 Broadband Gateway. Depending on the software loaded on the BGW210-700 Broadband Gateway, holding it for an elongated duration of time may reset the device to factory defaults.
 Referring to the diagram below, find the round Reset switch opening.
BGW210-700 Broadband Gateway Reset Switch Location

Press the reset button to initiate the following:
 Press the factory reset button for less than ten seconds to reboot the BGW210-700 Broadband Gateway, the indicator lights on the device will respond immediately and start blinking red within one second of the reset button being pressed.
 The lights will blink whether the button is still being pressed or has been released. The indicator lights will flash for a minimum of five seconds, even if the reset button is released within five seconds of being pressed. If the reset button is held for more than five seconds, it will continue to blink until released or until ten seconds have elapsed (see below).
 Press the factory reset button and hold for longer than ten seconds, to reset the device to the factory default shipped settings. If the button is held for ten seconds, the Power indicator continues to blink for an additional five seconds, and then the indicator lights return to their normal operating mode, whether or not the reset button is still depressed.
Warning: Resetting the BGW210-700 Broadband Gateway to factory defaults will require all configured settings to be reconfigured.

Technical Specification and Safety Information

Dimensions and Interfaces


Power Supply
This product is intended to be supplied with a Listed Direct Plug-In AC/DC power adapter marked Class 2 LPS power supply rated @ 12V 3A DC for all BGW210-xxx models.
The AC/DC power adapter supplied with this product is designed to ensure your personal safety and to be compatible with this equipment. Use only the power adapter that was provided with the gateway.
Environment
Operating temperature: 0°C to 41.7°C (32° F to 107° F); 8% to 95% (Non Condensing) Relative Humidity
Storage temperature: –40° C to 80° C (–40° F to 176° F)
Agency Approvels
North America
Safety Approvals:
 United States – UL 60950, Third Edition
EMC:
 United States – FCC Part 15 Class B, Subparts B, C, and E
Telecom:
 United States – CFR Part 68

Caring for the Environment by Recycling

When you see this symbol on an ARRIS product, do not dispose of the product with residential or commercial waste.

Recycling your ARRIS Equipment Please do not dispose of this product with your residential or commercial waste. Some countries or regions have set up systems to collect and recycle electrical and electronic waste items. Contact your local authorities for information about practices established for your region. If collection systems are not available, contact ARRIS Customer Service for assistance at www.arris.com/consumers.

Importent Safety Instructions

Warning: Do not use before reading these instructions.
Do not connect the Broadband Ethernet port (labeled ONT) to a carrier or carriage service provider’s telecommunications network or facility unless:
A) You have the written consent of the network or facility manager, or
B) The connection is in accordance with a connection permit or connection rules.
Connection of the Ethernet ports may cause a hazard or damage to the telecommunication network or facility, or persons, with consequential liability for substantial compensation.
WARNINGS
The power supply must be connected to an outlet. Do not defeat the protective earth connection. The direct plug-in power supply serves as the main power disconnect; locate the direct plug-in power supply near the product for easy access.
Product Ventilation
The gateway is intended for residential use. Position the gateway in an upright vertical position and locate it where temperatures remain within a range of 32° – 107°F (0° – 41.7°C) and where heat from the unit itself is not trapped. There must be at least two inches (2″) of clearance on all sides except the bottom.
Telecommunication Installation Cautions
 Never install telephone wiring during a lightning storm.
 Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations.
 Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the network interface.
 Use caution when installing or modifying telephone lines.
 Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electric shock from lightning
Electrical Safety Advisory
Telephone companies report that electrical surges, typically lightning transients, are very destructive to customer terminal equipment connected to AC power sources. This has been identified as a major nationwide problem. Therefore it is advised that this equipment be connected to AC power through the use of a surge arrestor or similar protection device.
Declaration of Conformance
Warning: This is a Class B product. In a domestic environment this product may cause radio interference, in which case the user may be required to take adequate measures. Adequate measures include increasing the physical distance between this product and other electrical devices. Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
United States: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
 Reorient or relocate the receiving antenna.
 Increase the separation between the equipment and receiver.
 Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
 Consult the dealer or an experienced radio/TV technician for help.

47 CFR Part 68 Information

United States: This device complies with 47 CFR Part 68 of the FCC Rules. Operation is subject to the following four conditions:
1. The Federal Communications Commission (FCC) has established Rules, which permit this device to be directly connected to the telephone network. Standardized jacks are used for these connections. This equipment should not be used on party lines or coin phones.
2. If this device is malfunctioning, it may also be causing harm to the telephone network; this device should be disconnected until the source of the problem can be determined and until repair has been made. If this is not done, the telephone company may temporarily disconnect service.
3. The telephone company may make changes in its technical operations and procedures; if such changes affect the compatibility or use of this device, the telephone company is required to give adequate notice of the changes. You will be advised of your right to file a complaint with the FCC.
4. If the telephone company requests information on what equipment is connected to their lines, inform them of:
 The telephone number to which this unit is connected.
 The ringer equivalence number. [0.XB] (Indicated on the label)
 The USOC jack required. [RJ11C]
 The FCC Registration Number. [US:AAAEQ##TXXXX] (Indicated on the label) The Ringer Equivalence Number (REN) is used to determine how many devices can be connected to your telephone line. In most areas, the sum of the REN’s of all devices on any one line should not exceed five (5.0). If too many devices are attached, they may not ring properly.
FCC Caution
Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits as set forth for an uncontrolled environment. This equipment should be installed and operated maintaining a minimum distance of 22 cm (9 inches) between the device and your body.

Service Requrement
In the event of equipment malfunction, if under warranty, we will exchange a product deemed defective. Under FCC rules, no customer is authorized to repair this equipment. This restriction applies regardless of whether the equipment is in or out of warranty.
Technical Support for Hardware Products: Customers inside North America: 888-944-4357 (888-944-HELP) Customers outside North America: 1-215-323-2345 For Spanish language support: 1-215-323-2346
Note: This product was tested for FCC compliance under conditions that included the use of shielded cables and connectors between system components. Changes or modifications to this product not authorized by the manufacturer could void your authority to operate the equipment.

ARRIS Contacts
Technical Services
For technical support on ARRIS products you can contact us by phone or on the web.
By Telephone
The Technical Assistance Center can be reached at:
1-888-944-HELP (4357)
On the Web
The Ask ARRIS web site gives you web access to service and support tools. You will need to register using your support contract ID and email address. Ask ARRIS is located at:
http://www.arris.com/support
There you will be able to access:
 Support Contact Information for all products
 Knowledge Base Information (also known as Solutions)
 User Documentation
 Current open support cases
 Ability to create a new support case (for technical support or repair and return)
 Training Webcast
By Email
Email addresses for ARRIS products will be provided with your account at Ask ARRIS.
Technical Training
For more information about our Global Knowledge Services Department and the programs we offer, e-mail us at:
[email protected]

Corporate Headquarters
ARRIS · Suwanee · Georgia · 30024 · USA
T: 1-678-473-2000 F: 1-678-473-8470
www.arris.com

https://usermanual.wiki/ARRIS/BGW210/view