This instruction manual applies to the LPT660 headphones sold under the brands: Zapet, Moonliness, Iceray, Haoba, Rockwin, Wpaier, Popova, Uonipow, E-Home, JKR, and others
Indicator light:
Pairing: the blue light blinking fast and voice remind BT mode.
Connecting: the blue light still blinking fast .
Charging: the LED light red while the battery is being charged, and will switch off when the power is charged enough
Charging power: Through computer USB OR DC5V port.
Charging time: Before the first usage please put to charge at least 4 hours continuously. For subsequent Charging 2-2.5 hours is sufficient for 10 hours of usage at average volume. The LED light red while the battery is being charged, and will switch off when the power is charged enough. NEVER leave it to over-charge.
Usage instruction
Pairing the headphone with cell phone:
Keep the headphone next to the cell phone within 1m, the closer the better.
Turn on the headphone, the voice remind: BT mode and ready for pair
Open the “search ” or “add new device” following the manual of cell phone, choose the headphone model name, pair successfully
Choose music:
When listening to the BT music,press “ pause” key, also press “Volume+” and “Volume-” key quickly to choose songs.
Adjust volume:
Long press “Volume+” and “Volume-” to adjust the volume
MP3 mode switch:
Long press button”MEQ” to switch the BT mode to MP3 mode, and just insert SD card, MP3 will pay music
Do not listen at high volume levels for long periods of time to prevent hearing damage.
Do not use the product if there is any potential danger.
Do not turn the volume too high to hear sounds around you, turn down the volume if you feel a tinnitus or the volume is too high.
Do not use the product in an environment that requires your special attention (e.g. in traffic).
Keep the product, accessories and packaging parts out of reach of children, to prevent accidents and choking hazards.
Always keep the product dry to avoid corrosion.
Do not use the product if you feelobvious discomfort, irritationor haveotheradverse reactions.
Do not expose the product to extreme temperatures below -15℃ (5℉) or above 55℃ (131℉), to maintain the lifespan of headset or battery.
Delivery includes
T2S Bluetooth headset
USB charging cable
Audio cable
User manual
Headset Overview
Charging and battery
Only use charging cable supplied by Bluedio, or may cause damage to the headset.
Warning
The DC voltage should be 5V and current should exceed 400mA.
Charging
The headset built-in battery is rechargeable and non-detachable. Do not replace the battery.
Switch off the headset before charging.
Connect the smaller plug of the charging cable to the USB socket of the headset; connect the other plug to the USB socket of your computer or other charging device; the LED lights up red and the headset is being charged.
When the headset is fully charged (about 1.5~2hrs), the LED lights up blue or LED goes out.
Pairing mode
Keep the MF button pressed until the LED lights up blue.
Reconnection mode
Keep the MF button pressed until the LED flashes blue.
Switching the headset off
Keep the MF Button pressed until the LED flashes blue then goes off.
Pairing the headset with your mobile phone
Keep the distance between the headset and your mobile phone (or other Bluetooth device) within 1 meter. The closer, the better.
Keep the MF button pressed until the LED lights up blue. The headset is in pairing mode.
Switch on the Bluetooth function of your mobile phone, on which start a search for Bluetooth devices.
Select “T2S” from the found Bluetooth devices to establish a Bluetooth connection to the headset. If necessary, enter the default PIN code “0000”.
Once the headset is paired with the mobile phone, the LED flashes blue.
Attention: If pairing is not successful within 60 seconds, the LED goes off and the Bluetooth pairing ends. Repeat the pairing procedure.
Disconnecting the headset with your mobile phone
Switch the headset off.
Or switch off the Bluetooth function of your mobile phone.
Or take the headset from your mobile phone 20m (60ft) away or even farther.
Reconnecting the paired headset to your mobile phone
Keep the distance between the headset and your mobile phone (or other Bluetooth device) within 1 meter. The closer, the better.
Keep the MF button pressed until the LED flashes blue. The headset is in reconnection mode.
Switch on the Bluetooth function of your mobile phone. The headset will automatically reconnect to it.
Answering a call
When there comes a call, the LED flashes blue; press the MF button once, or use your mobile phone to answer it.
Ending a call
Press the MF button once. Or use your mobile phone to end it.
Rejecting a call
After hearing a beep, keep the MF button pressed for around 2 seconds or use your mobile phone to reject it.
Call waiting (need to be supported by your mobile phone)
When you are on call 1, there comes call 2; to answer call 2 and keep call 1: keep the MF button pressed for around 2 seconds.
When call 2 ends, to switch back to call 1: keep the MF button pressed for around 2 seconds
Redialing the last call
Press the MF button twice
Voice dialing (need to be supported by your mobile phone)
Keep the MF button pressed for around 2 seconds
Voice prompt selection
Switch the headset on, press the MF button and Vol- button once at the same time to select English/Chinese/French/Spanish.
Muting
When you are on call, keep the Vol- button pressed to mute the Microphone; keep the Vol+ button pressed to cancel the muting.
Audio sharing
Connect the headset with your mobile phone via Bluetooth, then connect the headset to another headphone via audio cable.
Being a Bluetooth receiver
Connect the headset with your mobile phone via Bluetooth, then connect the headset to amplifier via audio cable.
Line-in connection
Connect the headset with your mobile phone via audio cable. (In this mode, the headset cannot be used for communication)
EQ adjustment (only in Bluetooth mode)
When the headset is playing music, press the Vol+ button and Vol- button once at the same time.
Track play/pause
Pause the track: press the Wheel switch once
Resume the track: press the Wheel switch once again.
Track selection/ Volume adjustment
Skip to the next track: push the Wheel switch down
Skip to the previous track: push the Wheel switch up
Turn the volume up: press the Vol (+) button once (to the maximum, there is a beep)
Turn the volume down: press the Vol (-) button once (to the minimum, there is a beep)
Technical specifications:
Driver units: 2 speakers (57mm)
Transducer type: dynamic
Bluetooth version: V4.1
Frequency response: 2.4GHz-2.48GHz
Operating distance: up to 10m (free space)
Profiles: A2DP, AVRCP, HSP, HFP
Speaker impendence: 16Ω
Frequency response: 20-20KHz
Sensitivity: 110dB
THD: <0.1%
Music time: about 40hrs
Talk time: about 45hrs
Standby time: about 1625hrs (around 50days)
Fully charged time: about 2hrs
Operating environment: -10 to 50℃
Technical specifications are subject to change without notice, we apologize for any inconvenience.
FAQ
Headset cannot be paired to your mobile phone.
Solution: Check if your mobile phone supports the HS or HF profile. Check if the Bluetooth search function of your phone is switched on. Check if your mobile phone is switched off. Check if the distance between the headset and your phone exceeds 10m.
Headset cannot be switched on.
Solution: The battery is flat. Recharge the battery.
Can the battery be replaced?
Answer: The battery is non-detachable and cannot be replaced.
Can the headset be used while driving?
Answer: Do not use the headset in an environment that requires your special attention. If necessary, use it for communication.
Bluetooth connection is suddenly interrupted within 10 meter.
Solution: Check if there is metal or other material interfering with the transmission.
No audio signal
Solution: Check if the headset is switched off. Check if the headset is paired. If necessary, pair the headset with the audio source again. Check the connection to your audio source. The volume may be adjusted too low, increase the volume.
Can the headset be used to control the APPs on your mobile phone.
Answer: Software settings of APPs may be varied, thus some APPs may not controlled by the headset.
The headset cannot be recharged.
Solution: Check the connection of USB plugs. If necessary, remove the USB cable and reconnect again. Switch the headset on then turn it off.
1. Watchband tightness standards: cross the watchband,can be added into an index finger as the standard;
2. Pairing connection for the first time, without using bluetooth pairing method, only need close NFC on the watchband to mobile phone NFC antenna location nearly .Smart Watch NFC antenna position ,please reference the overview products (diagram).
3. Use watchband for the first time, will be tight, hard to buckle into , pls follow as below methods: Put right index finger inside of the watchband ,from the top push button in.
Use watchband
1. Safe instructions and main precautions
1.1 The company reserves the right to revised the manual without any prior notice.
1.2 Please charge more than 2 hours before using
1.3 Security Code
To prevent others use your product without authorization,the original password is 1122.In order to ensure the security of your personal information, please modify the original password and remember it.
2. Product Introduction
2.1 Introduction
Components of Smart Watch
Power button: Turn on/off, Wake up, Shut down,Back;
USB:Charging and data function;
Touch screen: capacitive touch screen, the function can be operationed in capacitive touch screen.
2.2 Enter Quickly
After turn on,finger drag left enter the next menu, drag right to return back the menu;Finger drag from the top to
down, enter into the notification bar,from the bottom to top, back to the main menu.
Drag distance need drag over half of the screen,if drag too short, will be mistaken for a click.
The function icon can be place the position freely according to your ideas , click ok to sure.
2.3 Using the Clock screen
While using the Watch, press the Power button to open the Clock screen.Then click the central of screen to change clock type.
Clock screen
Setup ways:
method 1:turn on,on the Clock screen,click the central of screen to change clock type.,there are 3 types can be selected.
method 2:turn on,enter the menu :setup–phone setup–Standby menu–Unlock type selection.
2.4 Theme Settings
Setting Method:
Go into the smart watch menu: themes-theme Settings-select your theme
3. Operation Quickly
3.1 Download the synchronous software
Methods 1、turn on the menu of watches – enter into QR Codes directory, using mobile phone QR code scanning
software scan the QR code on the watch.。
Methods 2、Using mobile phone scan below QR code to download
QR code
Method 3,using mobile browser, enter the following URL to download http://c3.cli.im/FT5K1A
After download,according the prompts to install the application. This Program only support synchronization
between watch and android smart phone,will not charge mobile phone network traffic.
If you have downloaded relevant software from other channels , please check the software version,
please use the latest version of the synchronization software, to ensure the normal use of function.
If software version has upgraded, please update synchronization software.
3.2 Installation and use synchronization software
Android application software installation:
On smartphone, according to the normal android software installation, when installation complete,
can be stored into the phone memory or synchronization assistant software installation can be used.
Android applications use method: ( installed software already)
(smartphone)Enter the Settings –auxiliary Settings–bluetooth notice (services) click enter,
enable the service.
(when start using, there will be a warning, please select “ok”) software can be automatically run in the background,
synchronizing function can be used .as following:
synchronizing function
Click on the bluetooth notice, choose “notification service”,
in the “notice”,choose to push personal application or system application you need;
Telephone service function, including text messages and telephone;Looking for watch。
Note:when you use the back-end to clean up or close the back-end application software,
please do not close this bluetooth notification service,
if closed, sync will influence the watch with a mobile phone.
3.3 Bluetooth connectivity and synchronization function
3.3.1 from the mobile phone to connect Watch
Enter Mobile phone settings – turn on bluetooth – search equipment, when find GT08,
click choose matching, and select “yes” on the watch, matching success, when there is a phone book request,
please click “ok”,
it is better choose “next time no longer prompt” at the same time,
convenient for next time connection, the phone book will sync directly, not prompt again. Note:If has installed a synchronization software,
pls also turn on this synchronization software on mobile phone in auxiliary function,
after connection,within 2-5 seconds, the mobile phone terminal will show the bluetooth connected;
on smart watch at the same time,will prompts you automatic synchronization cellphone time,
it indicates that the synchronization function is enabled.When mobile phone have a new message coming,
will synchronization to smart watches in timely. 3.3.2From the smart watch to connect mobile phone
On the smart watch,select the bluetooth dialer – click to search bluetooth device –
find your smartphone (such as samsung 9500) – click connection;the continue process operation as 3.3.1 3.3.2From the smart watch to connect mobile phone On the smart watch,
select the bluetooth dialer – click to search bluetooth device – find your smartphone (such as samsung 9500)
– click connection;the continue process operation as 3.3.1 Note: At the same time,the mobile phone need turn on the bluetooth
and allow to be searched by around bluetooth products
3.4 Function menu description
3.4.1 Message mobile phones synchronous message or smart watch message
3.4.2 Bluetooth
3.4.3 Set up the state of the bluetooth, turn on or off.
3.4.4 Call Records
3.4.5 After connecting the bluetooth, you can view your call status of the near term。
Bluetooth Dialer :
From the watches to connect the mobile phone for matching;
3.4.6 Remote Notification
Synchronous Show the message from mobile phone terminal , such as: QQ, WeChat, messages, time, Twitter, Facebook etc.;
3.4.7 Remote Take Photos
Controlling from the watch,using mobile phone camera take pictures;Need turn on the android mobile phone’s camera advance.
3.4.8 Anti-lost
Watch looking for mobile phone or mobile phone looking for watch. Two-way anti lost;
3.4.9 Setup
Note: In the phone setting, you can set the clock type and theme;In the security Settings, the default security code: 1122
3.4.10 Pedometer
In pedometer Settings, drag to left, you can see steps and burn calories, speed, mileage etc.
movement information;
In the process of movement, if want to go back to the main menu, and don’t want to stop step function,
please press the power button.pedometer function will continue to run in the background.
Motion synchronization data, please see the behind dynamic capabilities.
3.4.11 Sleep Monitoring
According to your sleep time to show the quality of your sleep.
3.4.12 Sedentary Remind
Can set up the time, remind you need to take exercise;It is recommended that one time at least per hour;
3.4.13 QR code
Scan the QR code, can download the synchronization software, if have the new version software to upgrade,
please contact with our company, we will provided the new download address;Please do not use WeChat or QQ
,or others browser scanning and download.
3.4.14 Intelligent search
Searching for the relevant information on the watch
3.4.15 Clock
3.4.16 Calendar
3.4.17 Calculator
3.4.18 Profiles
3.4.19 File Manager
3.4.20 Music Player
Can play music on the watch and mobile phone music connected bluetooth;
3.4.21 Theme, as shown in the theme Settings
3.4.22 Camera
3.4.23 Video recording device
3.4.24 Photo
3.4.25 Video Player
3.4.26 Record
4.Precautions for use
4.1 Please charge fully before use, charging time need 1-2 hours.
4.2 Charge line can use android smartphone charge line and authentic charger;
Or use the standard configuration
accessories;
4.3 Bluetooth disconnect if exceeds the distance, after using two-way anti-lost,if do not reconnect again,
it cannot use the search function;
4.4 Using bluetooth,it will be disconnect occasionally,please reconnect(if over 5 minutes not connected,
need connect manually)When connection,
please pay attention to choose agree with the phone book synchronous;Otherwise,
it will not be able to show the calls from phone book;
4.5 Music function, because of there are different android mobile phone,
some will show the name of the song ,some mobile phone is can not show the name of the song, this is normal.
;
5. Dynamic movement data synchronization function
5.1 Download Dynamic movement back-end service software
QR code
Method one: scan the QR code, installation Dynamic movement
background services software;Installation method as above;
Method Two: Log in background services website: www.fundo.cc download dynamic movement APK;
5.2 Sport data storage and sharing 5.2.1 Registered ID and login dynamic server, to accurate accounting sport data and give you the correct guidance,pls set your parameters, including height, weight, age. 5.2.2 Connect Smart Watch and mobile phone bluetooth,
and connect the bluetooth synchronization software;Same as above 5.2.3 After do exercise, click the “reset” data on the watch, can store multiple data 5.2.4 In the mobile phone, use dynamic software synchronous data,
synchronization data to back-end to share and store.Back-end will record your movement process and data 5.2.5 Please reference the function and use introduction on the website about the other function
and new features for the dynamic movement software. 5.2.6 Dynamic service website:www.fundo.cc
6. NFC Application
6.1 The smart watch with NFC function(Near Filed Communication);
Bluetooth pairing password has been written into the smart watch when production on factory 6.2 Smart Watch paired with mobile phone bluetooth, turn on mobile phones bluetooth,
smart watch NFC antenna position close nearly to the mobile phone NFC antenna position
(the different phone will be on different position,
can be searched by move slowly in mobile phone’s back around),
the phone will automatically prompt the bluetooth pairing;
Then pairing as usual.After the smart watch pairing with mobile phones,
need to connect again,or disconnected,
only need two NFC antenna close nearly to contact, without any manual processing. 6.3 Write the content into smart watch NFC: 6.3.1 Mobile phone download the write NFC software ,
there are too many kinds of software sold on the market,we recommended TagWriter
it can be download easy,please installed like android software after downloading; 6.3.2 Written software instructions ( TagWriter for example):
1) open the software, as following figure (figure 1) View is to read,
to read data for NFC module .Please see the content what has been written.
Create and write is to write documents
2) Click Create and write go into the next interface:(figure 2)
3) Write in a bluetooth address and password, click New, shown as figure 3,
and then select bluetooth, shown as figure 4,
then searching the connected Bluetooth watch (such as M2)
4) click the device name M2, and then go into the next interface (figure 5),
click Next enter the Next step shown as figure 6, tick the write multiple NFC,
click Next ,in the next step, shown as figure 7.
Using mobile phone antenna position close to smart watch NFC antenna position,
wait for 2 seconds, watches and cell phone issued a “tick”at the same time,success shown as figure 8.
5) write other content, steps and methods are same as above, only in
step 3), choose a different content, it can be message or contacts.
7. Common Troubleshooting Guides
If have any problems when using the smart watch, please refer to the following terms and conditions.
If the problem still exists, please contact the dealer or the designated maintenance personnel.
7.1 Can not turn on
Press the power button too short, please press over 3 seconds.
Battery Power too low, please charge. 7.2 Shut down automatic Battery Power too low, please charge. 7.3 Using time is very short
Not fully battery power, please make sure Charging enough time (minimum 2 hours).
Use the SIM card, but the signal is very poor, lead to cell phone use big current. 7.4 can’t normal charge
Check whether the battery is available, the performance of the battery will reduce after a few years.
Check the charger is working correctly, change the new charger to try Check the connect USB charging line interface
try again. 7.5 Not show the caller’s name
When the bluetooth connection, it not choose to upload directory;or not tick uploaded phone book;
Reconnect again, do not sync the contacts, please reconnect again and pairing. 7.6 Voice quality is not good
Smart watch and the mobile phone too far away, please come close;
Or bluetooth signal is bad.
The mobile phone signal is bad, change another place to answer the phone. 7.7 Dynamic data can’t sync, because of not log in the back-end,
movement data can’t save in the back-end,please register and log in.
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the following measures
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions
(1) This device may not cause harmful interference,
and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
SAR:
The radiated output power of this device is below the FCC
radio frequency exposure limits. Nevertheless, the device
should be used in such a manner that the potential for human
contact is minimized during normal operation.
The exposure standard for wireless devices employs a unit of
measurement known as the Specific Absorption Rate, or SAR.
The SAR limit set by the FCC is 1.6 W/Kg. Tests for SAR are
conducted using standard operating positions accepted by the
FCC with the device transmitting at its highest certified power
level in all tested frequency bands. Although the SAR is
determined at the highest certified power level, the actual SAR
level of the device while operating can be well below the
maximum value. This is because the device is designed to
operate at multiple power levels so as to use only the power
required to reach the network. In general, the closer you are to
a wireless base station antenna, the lower the power output. To
avoid the possibility of exceeding the FCC radio frequency
exposure limits, human proximity to the antenna should be
minimized.
• Please turn off the controller before swapping controller modes.
• Press and held START for3 seconds to turn of the controller.
Bluetooth Connection
Controllers will auto reconnect to your devices once they have been paired.
Android (D-Input)
1. Pres and hold START for 1 second to power on the controller, LED wil blink once per cycle.
2. Press and hold SELECT for 3 seconds to enter pairing mode Blue LED will rapidly blink.
3. Go to your Android device’s Bluetooth seting, pair with [8Bitdox GamePad],
4. LED wil be solid blue when Connection is successful, USB Connection: connect your 8Bitdo controller to your Android device via USB Cable after step 1.
Windows (X-Input)
1. Press and hold START + X for l Second to power on the controller, LED will blink twice per cycle.
2. Press and hald SELECT for3 seconds to enter pairing mode. Blue LED will rapidly blink.
3. Go to your Windows devices Bluetooth setting: pair with [BBltdox GamePad(x].
4. LED will be solid blue when connection is successful. USB Connection: connect your 8Bitdo controller to your Windows device via USB Cable after step 1.
macOS
1. Press and hold START+A for 1 second to power on the controller, LED will blink three times per cycle.
2. Press and hold SELECT for3 Seconds to enter pairing mode. Blue LED wil rapidly blink.
3. Go to your macOS devices Bluetooth setting, pair with [Wireless Controller].
4. LED wil be solid blue when connection is successful. USB Connection: connect your 8Bitdo controller to your macOS device via USB Cable after step 1.
Switch (by default)
1. Press and hold START + Y for second to power on the controller, LED wil blink four times per Cycle.
2. Go to your Switch Home Page to click on Controllers, then click on Change Grip/Order.
3. Pres and hold SELECT for seconds to enter pairing mode. Blue LED will rapidly blink.
4. LED will be solid blue when connection is successful. When Connected to your Switch, DOWN+SELET = Switch HOME button.
Battery
Status
LED indicator
Low battery mode
LED blinks in red
Battery Charging
LED blinks in green
Battery fully charged
LED stops blinking in green
• Built-in 480 mAh Li-on with18 Hours of play time.
• Rechargeable via USB cable with 1-2 hour charging time.
• Press START for 8 seconds to force turn of your controller.
Power Saving
1. Sleep mode -1 minute with no Bluetooth connection.
2. Sleep mode – 15 minutes with Bluetooth connection but no use. Press START to wake up your controller.
1-Press START to turn on the controller.
2-Press and hold START for 3 seconds to turn off the controller.
3-Press and hold START for 8 seconds to force turn off the controller.
Bluetooth Connection
Switch
1. Press STARTHY to turn on the Controller, LEDs will start to rotate from left to right.
2. Press and hold PAIR for 2 seconds to enter pairing mode. LEDS will turn off for a second
then start to rotate from | left to right.
3. Go to your Switch Home Page to click on Controllers, then click on Change Grip/Order
and wait for controller to sync up. LED will become solid when connection is successful.
4. Controller will auto reconnect to your Switch with the press of START once it has been paired
STAR button = Switch screenshot button, Home button = Switch HOME button.
Android
1. Press START+B to turn on the controller, LED 1 wil start to blink
2. Press and hold PAIR for 3 seconds to enter pairing mode. LED wil rotate from let to right.
3. Go to your Android devices Bluetooth seting, pair with [8Bitdo SF30 Pro] or [8Bitdo SN30 Proj].
LED will become solid when connection is successful.
4. Controller will auto reconnect to your Android device with the press of START once it has been paired.
USB Connection: connect the controller to your Android device via USB Cable after step 1.
Windows
1. Press START+X to turn on the controller, LEDs 1.2 will start to blink.
2. Press and hold PAIR for3 Seconds to enter pairing mode. LEDs will rotate from left to right.
3. Go to your Windows devicer Bluetooth setting, pair with [BBltdo SF30 Pro] or [8Bitdo SN30 Pro].
LED will become solid when connection is successful.
4. Controller will auto reconnect to your Windows device with the press of START once it has been paired.
USB Connection: connect the controller to your Windows device via USB Cable after step 1
macOS
1. Press and hold START+A for l second to power on the controller, LEDs 1.2.3 will start to blink.
2. Press and hold PAIR for 3 seconds to enter pairing mode. LEDs will rotate from left to right.
3. Go to your macOS device’s Bluetooth setting, pair with [Wireless Controller].
LED will become solid when connection is successful.
4. Controller will auto reconnect to your Windows device with the press of START once it has been paired.
USB Connection: connect the controller to your macOS device via USB Cable after step 1.
T Turbo function
1. Hold the button you would like to set turbo functionality to and then press the STAR button to activate turbo
functionality.
2. HOME LED will blink when turbo functionality has been applied successfully.
3. All buttons with Turbo functionality activated will cause the HOME LED to blink, showing you that Turbo
functionality is active on that button.
4. To deactivate turbo function, hold the button with turbo functionality activated press the STAR button to
deactivate turbo functionality.
The HOME LED will no longer blink if you have successfully disabled turbo
functionality.
Analog sticks are not included.
This does not apply to Switch.
Battery
Status
LED indicator
Low battery mode
POWER LED blinks
Battery Charging
POWER LED stays solid
Battery fully charged
POWER LED turns off
Built-in 480 mAh Li-on with16 Hours of play time.
Rechargeable via its USB-C cable with 1-2 hour charging time.
Battery charging time might vary depending on the environment the controller is exposed to.
Power Saving
Sleep mode -1 minute with no Bluetooth connection
Sleep made – 15 minutes with Bluetooth connection but no use
• Please turn off the controller before swapping controller modes.
• Press and held START for3 seconds to turn of the controller.
Bluetooth Connection
Controllers will auto reconnect to your devices once they have been paired.
Android (D-Input)
1. Pres and hold START for 1 second to power on the controller, LED wil blink once per cycle.
2. Press and hold SELECT for 3 seconds to enter pairing mode Blue LED will rapidly blink.
3. Go to your Android device’s Bluetooth seting, pair with [8Bitdox GamePad],
4. LED wil be solid blue when Connection is successful, USB Connection: connect your 8Bitdo controller to your Android device via USB Cable after step 1.
Windows (X-Input)
1. Press and hold START + X for l Second to power on the controller, LED will blink twice per cycle.
2. Press and hald SELECT for3 seconds to enter pairing mode. Blue LED will rapidly blink.
3. Go to your Windows devices Bluetooth setting: pair with [BBltdox GamePad(x].
4. LED will be solid blue when connection is successful. USB Connection: connect your 8Bitdo controller to your Windows device via USB Cable after step 1.
macOS
1. Press and hold START+A for 1 second to power on the controller, LED will blink three times per cycle.
2. Press and hold SELECT for3 Seconds to enter pairing mode. Blue LED wil rapidly blink.
3. Go to your macOS devices Bluetooth setting, pair with [Wireless Controller].
4. LED wil be solid blue when connection is successful. USB Connection: connect your 8Bitdo controller to your macOS device via USB Cable after step 1.
Switch (by default)
1. Press and hold START + Y for second to power on the controller, LED wil blink four times per Cycle.
2. Go to your Switch Home Page to click on Controllers, then click on Change Grip/Order.
3. Pres and hold SELECT for seconds to enter pairing mode. Blue LED will rapidly blink.
4. LED will be solid blue when connection is successful. When Connected to your Switch, DOWN+SELET = Switch HOME button.
Battery
Status
LED indicator
Low battery mode
LED blinks in red
Battery Charging
LED blinks in green
Battery fully charged
LED stops blinking in green
• Built-in 480 mAh Li-on with18 Hours of play time.
• Rechargeable via USB cable with 1-2 hour charging time.
• Press START for 8 seconds to force turn of your controller.
Power Saving
1. Sleep mode -1 minute with no Bluetooth connection.
2. Sleep mode – 15 minutes with Bluetooth connection but no use. Press START to wake up your controller.
1. Insert Retro Receiver into console and then press the pairing button (the LED will rapidly blink).
2. Press your Joy-Con’s sync button.
3. Wait until your Retro Receiver’s LED is solid blue and the controller’s #1 LED stay on.
4. For next connection only need to press A button.
Nintendo Switch Joy-Con
For Nintendo Switch Pro controller
1. Insert Retro Receiver into console and then press the pairing button (the LED will rapidly blink).
2. Press your Switch Pro controller’s sync button.
3. Wait until your Retro Receiver’s LED is solid blue and the controller’s #1 LED stay on.
4. For next connection only need to press A button.
Nintendo Switch Pro controller
For 8Bitdo controllers
1. Power on 8Bitdo controller (Mode 1) to enter pairing mode.
2. Insert Retro Receiver into console and then press the pairing button (the LED will rapidly blink).
3. Wait until your Retro Receiver and your 8Bitdo controller’s LEDs are both solid blue.
4. Your controller is now paired.
8Bitdo controller
For Wii Remote/Wii MotionPlus controller
1. Insert Retro Receiver into console and then press the pairing button (the LED will rapidly blink).
2. Press the Wii Remote/Wii MotionPlus controller’s sync button.
3. Wait until your Retro Receiver’s LED is solid blue and the controller’s #1 LED stay on.
4. To re-sync after powering your console down. For Wii Remote: press 1 and 2 buttons. For Wii MotionPlus: press A button.
Wii RemoteWii MotionPlus controller
For Wii U Pro controller
1. Insert Retro Receiver into console and then press the pairing button (the LED will rapidly blink).
2. Press your Wii U Pro controller’s sync button.
3. Wait until your Retro Receiver’s LED is solid blue and the controller’s #1 LED stay on.
4. For next connection only need to press A button.
Wii U Pro controller
For PS3 controller
1. Download and Run 8Bitdo Retro Receiver Tools on your PC available for Mac and PC.
2. On your Retro Receiver, hold down the pairing button and connect it to your MAC/PC via USB.
3. Connect your PS3 controller to MAC/PC via USB.
4. Once your Retro Receiver and PS3 controller are both connected via USB, click the “Pair” button
in the software.
5. Once pairing is complete, you can insert your Retro Receiver into your console.
6. Now press the PS button on your PS3 controller.
7. Wait until your Retro Receiver’s LED is solid blue and the controller’s #1 LED stay on.
8. To re-sync after powering your console down, begin from step 6.
PS3 controller
For PS4 Controller
1. Insert Retro Receiver into console and then press the pairing button (the LED will rapidly blink).
2. Press and hold the PS and Share buttons until the lightbar begins to strobe quickly in double.
3. Wait until your Retro Receiver’s LED is solid blue and the controller’s lightbar stay on.
4. For next connection only need to press PS button and wait until receiver’s LED is solid blue.
PS4 Controller
Instruction Manual for X-input
For 8Bitdo controllers
1. Power on 8Bitdo controller (Mode 1) to enter pairing mode.
2. Insert Retro Receiver into console and then press the pairing button (the LED will rapidly blink).
3. Wait until your Retro Receiver and your 8Bitdo controller’s LEDs are both solid blue.
4. Your controller is now paired.
8Bitdo controllers.X-inputstructure of 8Bitdo controllers.X-input
For Wii Remote/Wii MotionPlus controller
1. Insert Retro Receiver into console and then press the pairing button (the LED will rapidly blink).
2. Press the Wii Remote/Wii MotionPlus controller’s sync button.
3. Wait until your Retro Receiver’s LED is solid blue and the controller’s #1 LED stay on.
4. To re-sync after powering your console down. For Wii Remote: press 1 and 2 buttons. For Wii MotionPlus: press A button.
For Wii U Pro controller
1. Insert Retro Receiver into console and then press the pairing button (the LED will rapidly blink).
2. Press your Wii U Pro controller’s sync button.
3. Wait until your Retro Receiver’s LED is solid blue and the controller’s #1 LED stay on.
4. For next connection only need to press A button.
Wii U Pro controller.X-input
For PS3 controller
1. Download and Run 8Bitdo Retro Receiver Tools on your PC available for Mac and PC.
2. On your Retro Receiver, hold down the pairing button and connect it to your MAC/PC via USB.
3. Connect your PS3 controller to MAC/PC via USB.
4. Once your Retro Receiver and PS3 controller are both connected via USB, click the “Pair” button
in the software.
5. Once pairing is complete, you can insert your Retro Receiver into your console.
6. Now press the PS button on your PS3 controller.
7. Wait until your Retro Receiver’s LED is solid blue and the controller’s #1 LED stay on.
8. To re-sync after powering your console down, begin from step 6.
PS3 controller.X-input
For PS4 Controller
1. Insert Retro Receiver into console and then press the pairing button (the LED will rapidly blink).
2. Press and hold the PS and Share buttons until the lightbar begins to strobe quickly in double.
3. Wait until your Retro Receiver’s LED is solid blue and the controller’s lightbar stay on.
4. For next connection only need to press PS button and wait until receiver’s LED is solid blue.
PS4 Controller.X-input
Instruction Manual for PS3
For 8Bitdo controllers
1. Power on 8Bitdo controller (Mode 1) to enter pairing mode.
2. Insert Retro Receiver into console and then press the pairing button (the LED will rapidly blink).
3. Wait until your Retro Receiver and your 8Bitdo controller’s LEDs are both solid blue.
4. Your controller is now paired.
8Bitdo controllers -ps3
For Wii Remote/Wii MotionPlus controller
1. Insert Retro Receiver into console and then press the pairing button (the LED will rapidly blink).
2. Press the Wii Remote/Wii MotionPlus controller’s sync button.
3. Wait until your Retro Receiver’s LED is solid blue and the controller’s #1 LED stay on.
4. To re-sync after powering your console down. For Wii Remote: press 1 and 2 buttons. For Wii MotionPlus: press A button.
Wii RemoteWii MotionPlus controller.PS3
For Wii U Pro controller
1. Insert Retro Receiver into console and then press the pairing button (the LED will rapidly blink).
2. Press your Wii U Pro controller’s sync button.
3. Wait until your Retro Receiver’s LED is solid blue and the controller’s #1 LED stay on.
4. For next connection only need to press A button.
Thank You For Purchasing our 8Bitdo Cube Speaker.
Ready carefully and follow all instructions in this User’s Manual before you use
8 Bitdo Cube Speaker
Keep this User’s Manual in a convenient location for future reference
Safety Instructions
This Product Is specially designed based on the full attention to safety ;
in order to make sure the accident-free operation
please abide the guidelines lsited below
Always position the unit on a stable and level surface.Unstable surface can cause the unit to topple and fall , resulting in possible damage or injury
Do not drop ,unpack,open,beat,curve,prink and burn the unit
Avoid using the unit nearby basins or sinks where it may come in contact with water
Do not place any ware with full water on the top of unit ,such as vase,glass,pot,and please avoid placingcandle on the speaker surface as well
Protect the using of the unit from any overheating devices
(such as radiator,heating installation,cooking stove or other heating device)
Regardless of what reasons cause the unit damage ,please ask for the maintenance personnel to repair
if you want to do the cleaning ,please turn off the unit and unplug the power cable from the outlet first
Set the volume properly to prevent injury to the unit and your health
Correct Disposal of this product.This marking indicates that this product should not be disposed with other household wastes
throughout the EU.To prevent possible harm to the environment or human helth from uncontrolled waste disposal,
recycle it responsibly to promote the sustainable resue of material resources.To return your used device,
please use the return and collection systems or contact the retailer where the product was purchased.
They can take this product for environmental safe recycling.
WARNING
The battery (battery or batteries or battery pack) shall not be exposed to excessive heat such as sunshine,fire or the like
no naked flame sources,such as lighted candles,should be placed on the apparatus
CAUTION:Danger of explosion if battery is incorrectly replaced.Replace only with the same pr equivalent type
Package Contents
8Bltdo Cube Speaker maln unitx 1
USB charging cable x 1
Aux cable x 1
.User’s manual x 1
Fit Models
• Apply to : all iPhone and iPad series, Smartphones, Laptop, Tablets and other Bluetooth devices.
• Work with any device with standard 3.5mm earphone Jack via the Included Aux cable for connecting, such as MP3, PSP,
Mobile phone…,etc
Outstanding Features
8Bitdo Cube Speaker is compatible with all wireless Bluetooth devices such as iPad, iPhone, Smartphones, Laptops,
Tablets and other Bluetooth devices. It is portable, wireless, hands-free.
Just place it anywhere in a room and enjoy pristine streaming audlo from your phone, computer, or other Bluetooth devices.
Bring music, movles, and all your mobile audio vibrantly to life–all in the palm of your hand.
Go Anywhere and Go Wireless
Easily compatible with iPhone, iPad, mobile phones, computers, tablets, or any other Bluetooth-enabled device
Wireless working range is up to 8-12 meters, no cords, no hassle
Calling and Conference on the Go
With a powerful, built-in microphone, it can freas you to share clean-sounding conference calls or personal calling
anywhere–in the office, car, at home, alone, or with a group
Good sound system, enjoy your life
Special speaker drive unit with woofer, amp up your Music, Movies, Games to let you experience the richest sound Built-in
rechargeable battery, up to 6 hours of continuous play
Crafted outlook and function design.
AUX IN, almost work with any player.
Sleep mode to save the battery for long time play.
Part Names
Main Unit
Power on/Power off
Volume –
Multi-function button (playł pausel speaker)
Volume +
USB charging port
Charging indicator
Bluetooth indicator
AUX IN
Components of 8Bitdo Cube Speaker
Basic Operation
• Power on/Power off
1. Power on : Holding power button until hearing starting sound.
2. Power off : Holding power button until hearing ending sound. Connectlon
1. Work with phone
Power on the unit, and coming with a short Bluetooth hint sound from the unit,
the Bluetooth function is on, the blue Bluetooth indicator lights up at the same time,
these show the unit is enter pairing mode. Turm on the Bluetooth function in your phone,
and search the Bluetooth device, then, your phone will find the device named “8Bitdo Cube”,
Atone will sound to confirm the device has paired successfully.
Note: Please reference the user’s manual of your cell phone for the detalls about Bluetooth connection.
2. Work with tablet PC
Please refer to the above phone connection operation steps
3. Work with laptop/ notebook computer /PC
As the Bluetooth version for laptop/ notebook computer /PC is various, the connection methods are different as well,
if you can not connect with the unit for play on first use,
you may need to install a new version of the Bluetooth driver in your laptop in advance.
Please reference the instructions of laptop for details.
Play mode
Bluetooth mode: play music via Bluetooth connection
AUX mode: play music via AUX cable. Note: Bluetooth mode is unavailable when speaker in AUX mode.
Note: Bluetooth mode is unavailable when speaker in AUX mode.
Play the music
Play music via Bluetooth
Follow the steps above to pair the Bluetooth device and the unit
Enter in the Bluetooth device audio play menu, choose your favorite music to play
Press the multi-function button to pause or play your music as you need
Holding -/+ button to adjusting volume, press -/+ button to next/previous musi
AUX IN
Connect the audio device via Aux cable to the “Aux IN” port at the back of unit
Choose directly your favorite music in the audio device to play
Note: Next/Previous music function is unavailable at AUX IN connection
Adjusting the volume
Press the volume button on the unit or control the audio device volume directly to adjust the volume .
Note: Next/Previous music function is unavallable at AUX IN connection
Hands free function
The unit will play your phone ringtone when there is a incoming cal
At this time, press the multi-function button to answer the phone, and talk through the microphone
Charge
Connecting to any standard USB port Vla mlcro USB cable. (such as PC, USB power adapter…etc.)
The charging indicator will light up while charging
It will be fully charge in 2.5 hours.
The charging indicator working mode:
Red LED on : the unit is charging
Red LED off : the battery is fully charged
Note: if the unit is not to be used longer than 7 days, please charge the unit for 10 minutes before turn on the unit.
Technical parameters
Note: All specifications are subject to change without notice.
Product Name: 8Bitdo Cube Speaker.
Power Supply: USB 5V.
Built-in Lithium lon batteries: 3.7V 800mAh.
Output power: RMS 3W.
Bluetooth Profile Supported: A2DP, AVRCP.
Working range: up to 8-12m.
Working atmosphere: 0°C-40°C/20%-90%RH.
Maintenance
Please follow the instructions below before clear the unit
Power off the unit first before clear
Use a soft, dry, lint-free cloth to wipe gently
Do not use alcohol, benzene, thinners or other chemical detergents as these can cause the casing to be
If the unit will not be used for an extended period of time, power off the unit and place the unit with accessorles Into the package
Do not set the unit in a damp, high temperature or the sun point-blank place
Troubleshooting
Question: Can’t pair successfully after multiple connections?
Solution
1. Check if the blue Bluetooth indicator lights on, if the indicator goes off, please slide the ON/OFF switch to “ON”,
if the blue Bluetooth indicator doesn’t light on yet, please charge the unit.
2. Perhaps there are many Bluetooth devices around the surroundings to interfere the searching, please close the
Bluetooth function in the device you don’t need
3. Power off and then power on the unit, to restart the Bluetooth function of the unit or your Bluetooth device.
4. Unplug the AUX cable from the unit, and re-palr the unit and the Bluetooth device.
Questlon: The Sound occurs staccato when play ?
Solution :
1, Make sure the working distance is in 8-12m.
2. Clear away the block between the unit and the Bluetooth device to prevent the poor connecting.
3. Please check if the unit and the Bluetooth device is in low battery,
if so, please charge the unit and your Bluetooth device
Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection agalnst harmful
Interference In a residential Installation. This equipment generates uses and can radiate radio frequency energy and,
if not installed and used in accordance with the instructions,may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV techniclan for help.
FCC Radlatlon Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
1. Plug the 2.4G Retro Receiver into your NES / SFC / SNES Classic Edition.
2. Press START on your controller to connect to the Retro Receiver.
3. LED will be solid blue when connection is successful.
Home Menu Access for NES/SNES/SFC Classic Edition.
SELECT + DOWN = RESET
If connection is lost or you wish to pair with a new retro receiver, press and hold SELECT on the
controller for 3 seconds. Blue LED will rapidly blink and be solid blue when connection is successful
Windows/macOS/Android (wired connection)
1. Connect the controller to your Windows/macOS/Android via the USB cable.
2. LED will be solid blue when connection is successful.
X-Input: press and hold START+X for 3 seconds, blue LED blinks twice to indicate mode activation.
D-Input: press and hold START+B for 3 seconds, blue LED blinks twice to indicate mode activation.
macOS: press and hold START+A for 3 seconds, blue LED blinks twice to indicate mode activation.
Default mode: D-input.
Status
LED indicator
Low battery mode
POWER LED in Red
Battery Charging
POWER LED in green
Battery fully charged
POWER LED turns off
Built-in 180 mAh Li-on with 25 Hours of play time.
Rechargeable via USB cable with 60 minutes charging time.
Power Saving
Sleep mode – 15 minutes with wireless connection but no use.
Support
Please visit support.8bitdo.com for further information and additional support.
Controllers will auto reconnect to your devices once they have been paired
Android (D-input)
1. Press and hold POWER for 1 second to power on the controller, LEDs will blink once per cycle.
2. Press and hold PAIR for 3 seconds to enter pairing mode. Blue LEDs will rapidly blink.
3. Go to your Android device’s Bluetooth setting, pair with [8Bitdo xx Pro].
4. LEDs will be solid blue when connection is successful.
USB Connection:connect your 8Bitdo controller to your Android device via USB Cable after step 1
Windows (X-input)
1. Press and hold POWER + X for 1 second to power on the controller, LEDs will blink twice per
cycle.
2. Press and hold PAIR for 3 seconds to enter pairing mode. Blue LEDs will rapidly blink.
3. Go to your Windows device’s Bluetooth setting, pair with [8Bitdo xx Pro(x)].
4. LEDs will be solid blue when connection is successful.
USB Connection:connect your 8Bitdo controller to your Android device via USB Cable after step1
macOS
1-Press and hold POWER + A for 1 second to power on the controller,
LEDs will blink three times per cycle
2-Press and hold PAIR for 3 seconds to enter pairing mode.Vlue LEDs will rapidly blink
3-Go to your macOS device’s Bluetooth setting ,pair with [Wireless Controller]
4-LEDs will be solid blue when connection is successful.
.USB connection : connect your 8Bitdo controller to your macOS device via USB cable after step1
Switch (by default)
1.press and hold POWER+Y for 1 second to power on the controller,
LEDs will blink four times per cycle
2.Go to your Switch Home Page to click on Controllers,then click on Change Grip/Order
3.Press and hild PAIR for 3 seconds to enter pairing mode.Blue LEDs will rapidly blink
4.LEDs will be solid blue when connection is successful
.When Connected to your Switch ,POWER button = Switch HOME button;
PAIR button = Switch screenshot button
Battery
Status
LED indicator
Low battery mode
LEDS blink in red
Battery Charging
LEDS blink in Green
Battery fully charged
LEDs stop blinking in green
Built-in 480 mAh Li-on with 18 Hours of play time.
Rechargeable via USB cable with 1-2 hour charging time.
Press POWER for 8 seconds to force turn off your controller
Power Saving
Sleep mode -1 minute with no bluetooth connection
sleep mode – 15 minutes with Bluetooth connection but no use
Press POWER to wake up your controller
Support
.Please visit http://support.8bitdo.com for further information and additional support