JBL BAR Soundbar Pairing Instructions (Fix Auto-pair)

How do I pair the subwoofer to my JBL BAR soundbar if pairing does not happen automatically?

Normal pairing is automatic, and happens when you first switch both devices on. If pairing does not take place automatically, or you have to force new pairing, here is what to do: Turn on the soundbar and the subwoofer. If the connection is lost, the LED indicator on the subwoofer blinks slowly. Second, press the CONNECT button on the subwoofer to enter pairing mode. The LED indicator on the subwoofer blinks quickly. Third, press and hold the DIM DISPLAY button on the remote control for 5 seconds, followed by short press on BASS+, and BASS- button in sequence. Panel display will show “PAIRING”. If pairing succeeds, the LED indicator on the subwoofer lights up, and the soundbar display will show “DONE”. If pairing fails, the indicator on the subwoofer blinks slowly. Lastly, if the pairing fails, repeat the steps above. If you have continued trouble performing the pairing, please try to switch off all wireless devices in the home, then try again. This means routers, TV sets with wireless functions, telephones, computers etc. Since overcrowding on the 2.4 GHz frequency now often causes problems, eliminating all this activity makes space for the Bar to establish its connection, and you should be able to pair without problems. Afterwards, you can switch your devices on again. Often, all will now work fine, and if not, you will know which devices are doing the interference.

Reset / Change Pairing Source on JBL Everest / Everest Elite

How do I reset my Everest or Everest Elite headphone to pair with another Bluetooth source?

With the headphone in OFF state, press and hold the ON/OFF button for about 7 seconds for the Everest, 16 seconds for the Everest ELITE models. (ELITE changes to 7 seconds as well from software 0.5.6). Bluetooth memory is now erased, and new pairings can be made. An ELITE headphone permits pairing with one source device at a time. If you do not want to do a complete reset as described above, you can use the following method. Without reset, ELITE will try to re-pair with the last source when switched ON. If the last source is not detected, maybe because you want to use another source device, switch the ELITE off and on again, and make sure that the last source device you used is no longer switched ON. This way the ELITE will not be able to “see” the old source, and it will search for a new one. Now the ELITE will again search for the last paired source, and since it cannot find it after some seconds, it will switch back to be open for pairing with a new source. The LED will blink red/blue as an indication of this. The Everest BT models permit pairing with two source devices simultaneously. If you have used both source pairings, and want to pair to a third source, please perform the reset as described above (hold the ON/OFF button for about 7 seconds with the Everest OFF). Now you can again pair two source devices.

JBL Xtreme2 Manual

JBL Xtreme2
JBL Xtreme2

JBL Xtreme2 Manual

 

1. What’s in the box
What’s in the box

 

2. Buttons
Buttons

 

3. Connections
Connections

 

4. Bluetooth®
1. Bluetooth connection
Bluetooth connection

 

2. Music control

Music control

 

3. Speakerphone
Speakerphone

 

5. Voice assistant
Tap “Voice Assistant” in the JBL Connect app, to make the “ ” button as the activation key of Siri or Google Now on your phone.

Voice assistant

Press the “|>” button on the speaker to activate Siri or Google Now on your phone.
Please make sure the Siri or Google Now is enabled on your phone.

Activate Siri or Google Now on your phone

6. JBL Connect+

Wirelessly links more than 100 pcs JBL Connect+ compatible speakers together.

Play music on one of your JBL speakers and then press the JBL Connect+ button on all desired speakers to start pairing. All the other JBL speakers will play same music from the music source.

Download the JBL

Download the JBL Connect app for the following features: stereo setup, firmware upgrade, and device renaming.

JBL Connect

7. LED Behavior

LED Behavior

 

8. Warning
Warning

JBL Xtreme 2 is IPX7 waterproof.

IMPORTANT: To ensure that the JBL Xtreme 2 is waterproof, please remove all cable connections and tightly close the cap; exposing the JBL Xtreme 2 to liquids without doing so may result in permanent damage to the speaker. And do not expose JBL Xtreme 2 to water while charging, as doing so may result in permanent damage to the speaker or power source.

IPX7 waterproof is defined as the speaker can be immersed in water up to 1m for up to 30 minutes.

If the speaker will not be used for a long period of time, please recharge the battery at least once every 3 months. Battery life will vary due to usage patterns and environmental conditions.

9. Specifications

• Bluetooth® version: 4.2
• Support: A2DP V1.3, AVRCP V1.6, HFP V1.6, HSP V1.2
• Transducer: Woofer 2 x 2.75 inch
• Tweeter: 2 x 20 mm
• Rated power: 2 x 20W RMS Bi-amp (AC mode)
• Frequency response: 55Hz–20kHz
• Signal-to-noise ratio: >80dB
• Power supply: 19V 3A
• Battery type: Lithium-ion Polymer 36Wh (Equivalent to 3.7V10000mAh)
• Battery charge time: 3.5hours
• Music play time: up to 15 hours (varies by volume level and audio content)
• USB charge out: 5V / 2A (maximum)
• Bluetooth® transmitter power: 0-12.5 dBm
• Bluetooth® transmitter frequency range:
2.402 – 2.480 GHz
• Bluetooth® transmitter modulation: GFSK, π/4 DQPSK, 8DPSK
• Dimension (H x W x D): 136 x 288 x 132 mm
• Weight: 2393g

Bluetooth

The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth
SIG, Inc. and any use of such marks by HARMAN International Industries, Incorporated is under license. Other trademarks and trade names are those of their respective owners.

ANATEL

Questions about your JBL Xtreme2? Post in the comments!
Download JBL Xtreme2 Manual [PDF]

JBL Free Wireless Earbuds Manual

JBL Free Wireless Earbuds
JBL Free Wireless Earbuds

JBL Free Wireless Earbuds Manual

1. What’s in the box

What’s in the box

2. Customize your fit

a. Mix and match ear tips and silicone sleeves for a perfect fit and audio performance.

Mix and match ear tips

b. Installation

Installation

3. Wireless Device Pairing
a. First time pairing with device:
Step 1 – Ensure to give the ear pieces a full charge before initiating pairing.
*Ear pieces and charging case are packed separately.

Ensure to give the ear pieces a full charge

Step 2 – Remove right ear piece from case, it will turn on automatically, entering pairing mode (alt. blue/white).

Remove right ear piece from case

Step 3 – From device, go to Bluetooth menu.

go to Bluetooth menu

Step 4 – Remove left ear piece from case, it will automatically connect with the right ear piece.

Remove left ear piece from case

b. From second time onwards: Wireless connections are automatically established when the headphones are taken out of the case.

c. Ear pieces automatically power off and recharge when put in the charging case.

Ear pieces automatically power off and recharge

* To turn on ear pieces manually, long press the button on ear piece for 5s.

4. a. Buttons

Buttons

 

b. Manual power on and off

Manual power on and off

 

5. Charging

Charging

 

6. Manual controls for special situations

a. Manual Bluetooth pairing to device when ear pieces do not pair automatically.

Step 1 – Long press (>8s) right ear piece button when powered off

Long press

Step 2 – Choose JBL Free

Choose JBL Free

Choose “JBL Free” to connect

b. Manual pairing of left and right ear pieces when connection is lost.

Manual pairing of left and right ear pieces

c. Manual power off.

 Manual power off

 

7. a. LED Behaviors

LED Behaviors

b. Specifications

• Model: JBL Free X
• Bluetooth version: 4.2
• Support: A2DP V1.3, AVRCP V1.5, HFP V1.6
• Headset Battery type: Lithium-ion polymer (3.7V, 85mAh)
• Bluetooth transmitter power < 9.5dBm
• Bluetooth transmitter frequency range: 2.402 – 2.480GHz
• Bluetooth transmitter modulation: GFSK, π/4 DQPSK, 8DPSK
• Dynamic drivers: 5.6mm
• Frequency Response: 10Hz – 22 KHz
• Charging case battery: 1,500 mAH (est)
• Earbuds Battery life: Up to 4 hours
• Charging time: < 2 hours
• Compatibility: Use with Phones, Tablets, Computers
• Weight : 99g

IC RF Exposure Information and Statement
The SAR limit of Canada (C) is 1.6 W/kg averaged over one gram of tissue. Device types:

(IC: 6132A-JBLFREEX) has also been tested against this SAR limit According to this standard, the highest SAR value reported during product certification for head use is 0.033W / kg.

The device was tested for typical bodily operations where the product was kept 5 mm from the head.

To maintain compliance with IC RF exposure requirements, use accessories that maintain a separation distance of 0mm between the user’s head and the back of the headset. The use of belt clips, holsters and similar accessories shall not contain metal parts in its assembly. Use of accessories that do not meet these requirements may not comply with IC RF exposure requirements and should be avoided.

Head operation
The device was subjected to a typical head manipulation test. In order to comply with RF exposure requirements, a minimum separation distance of 0 cm must be maintained between the user’s ear and the product (including the antenna). Head exposure that do not meet these requirements may not meet RF exposure requirements and should be avoided. Use only the supplied or approved antenna.

 

FCC AND IC STATEMENT FOR USERS
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND

(2)THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. CAN ICES-3 (B) / NMB-3 (B).  FEDERAL COMMUNICATION COMMISSION INTERFERENCE STATEMENT
THIS EQUIPMENT HAS BEEN TESTED AND FOUND TO COMPLY WITH THE LIMITS FOR A CLASS B

DIGITAL DEVICE, PURSUANT TO PART 15 OF THE FCC RULES. THESE LIMITS ARE DESIGNED TO PROVIDE REASONABLE PROTECTION AGAINST HARMFUL INTERFERENCE IN A RESIDENTIAL INSTALLATION. THIS EQUIPMENT GENERATES, USES AND CAN RADIATE RADIO FREQUENCY ENERGY
AND, IF NOT INSTALLED AND USED IN ACCORDANCE WITH THE INSTRUCTIONS, MAY CAUSE HARMFUL INTERFERENCE TO RADIO COMMUNICATIONS. HOWEVER, THERE IS NO GUARANTEE THAT
INTERFERENCE WILL NOT OCCUR IN A PARTICULAR  NSTALLATION. IF THIS EQUIPMENT DOES CAUSE HARMFUL INTERFERENCE TO RADIO OR TELEVISION RECEPTION, WHICH CAN BE DETERMINED BY TURNING THE EQUIPMENT OFF AND ON, THE USER IS ENCOURAGED TO TRY TO CORRECT THE  INTERFERENCE BY ONE OR MORE OF THE FOLLOWING MEASURES:

• REORIENT OR RELOCATE THE RECEIVING ANTENNA.
• INCREASE THE SEPARATION BETWEEN THE EQUIPMENT AND RECEIVER.
• CONNECT THE EQUIPMENT INTO AN OUTLET ON A CIRCUIT DIFFERENT FROM THAT TO WHICH THE
RECEIVER IS CONNECTED.
• CONSULT THE DEALER OR AN EXPERIENCED RADIO/TV TECHNICIAN FOR HELP.

INSTRUCTIONS FOR USERS ON REMOVAL, RECYCLING AND DISPOSAL OF USED BATTERIES FOR PRODUCTS WITH A BUILT-IN BATTERY THAT LASTS FOR THE LIFETIME OF THE PRODUCT,
REMOVAL MAY NOT BE POSSIBLE FOR THE USER. IN THIS CASE, RECYCLING OR RECOVERY CENTERS HANDLE THE DISMANTLING OF THE PRODUCT AND THE REMOVAL OF THE BATTERY. IF, FOR ANY REASON, IT BECOMES NECESSARY TO REPLACE SUCH A BATTERY, THIS PROCEDURE MUST BE PERFORMED BY AUTHORIZED SERVICE CENTERS.

IN THE EUROPEAN UNION AND OTHER LOCATIONS, IT IS ILLEGAL TO DISPOSE OF ANY BATTERY WITH HOUSEHOLD TRASH. ALL BATTERIES MUST BE DISPOSED OF IN AN ENVIRONMENTALLY SOUND MANNER. CONTACT YOUR LOCAL WASTE-MANAGEMENT OFFICIALS FOR INFORMATION REGARDING THE ENVIRONMENTALLY SOUND COLLECTION, RECYCLING AND DISPOSAL OF USED BATTERIES. WARNING: DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY REPLACED. TO REDUCE RISK OF FIRE OR BURNS, DON’T DISASSEMBLE, CRUSH, PUNCTURE, SHORT EXTERNAL CONTACTS, EXPOSE
TO TEMPERATURE ABOVE 60°C (140°F), OR DISPOSE OF IN FIRE OR WATER. REPLACE ONLY WITH SPECIFIED BATTERIES.

THE SYMBOL INDICATING ‘SEPARATE COLLECTION’ FOR ALL BATTERIES AND ACCUMULATORS SHALL BE THE CROSSED-OUT WHEELED BIN SHOWN BELOW:

 WHEELED BIN

IN CASE OF BATTERIES, ACCUMULATORS AND BUTTON CELLS CONTAINING MORE THAN 0.0005% MERCURY, MORE THAN 0.002% CADMIUM OR MORE THAN 0.004% LEAD, SHALL BE MARKED WITH THE CHEMICAL SYMBOL FOR THE METAL CONCERNED: Hg, Cd, OR Pb RESPECTIVELY. PLEASE REFER TO THE BELOW SYMBOL:

WARNING
DO NOT ATTEMPT TO OPEN, SERVICE, OR DISASSEMBLE THE BATTERY | DO NOT SHORT CIRCUIT | MAY EXPLODE IF DISPOSED OF IN FIRE | RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE | DISPOSE OR RECYCLE USED BATTERIES ACCORDING TO THE INSTRUCTIONS

ANATEL

Bluetooth

The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by HARMAN International Industries, Incorporated is under license. Other trademarks and trade names are those of their respective owners.

Questions about your JBL Free Wireless Earbuds? Post in the comments!
Download JBL Free Wireless Earbuds Manual [PDF]

JBL Clip3 Manual [Bluetooth Clip-on Speaker]

JBL Clip3
 JBL Clip3

JBL Clip3 Manual [Bluetooth Clip-on Speaker]

1. What’s in the box

What’s in the box

2. Buttons

Buttons

3. Connections

Connections

4. Bluetooth®

1. Bluetooth connection

Bluetooth connection

 

2. Music control

Music control

 

5. Speakerphone

Speakerphone

 

6. LED indication

LED indication

 

7. Carabiner

Carabiner

IMPORTANT: The carabiner of JBL Clip 3 is not for climbing.

 

8. Warning

Warning

JBL Clip 3 is IPX7 waterproof.

IMPORTANT: To ensure that the JBL Clip 3 is waterproof, please remove all cable connections and tightly close the cap; exposing the JBL Clip 3 to liquids without doing so may result in permanent damage to the speaker. And do not expose JBL Clip 3 to water while charging, as doing so may result in permanent damage to the speaker or power source.

IPX7 waterproof is defined as the speaker can be immersed in water up to 1m for up to 30 minutes. If the speaker will not be used for a long period of time, please recharge the battery at least once every 3 months. Battery life will vary due to usage patterns and environmental conditions.

9. Specifications

• Bluetooth version: 4.1
• Support: A2DP V1.2, AVRCP V1.5, HFP V1.5, HSP V1.2
• Transducer: 1 x 40mm
• Output power: 1 x 3W
• Frequency response: 120Hz – 20kHz (-6dB)
• Signal-to-noise ratio: >80dB
• Battery type: Lithium-ion polymer (3.7V/1000mAh)
• Battery charge time: 3 hour @ 5V, 0.5A
• Music playing time: up to 10 hours (varies by volume level and audio content)
• Bluetooth transmitter power: 0 – 9dBm
• Bluetooth transmitter frequency range: 2.402 – 2.480GHz
• Bluetooth transmitter modulation: GFSK, /4 DQPSK, 8DPSK
• Dimensions (H x W x D): 137 x 97 x 46 (mm) \ 5.4″ x 3.8″ x 1.8″
• Weight: 210g \ 0.46 lbs

Bluetooth

The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by HARMAN International Industries, Incorporated is under license. Other trademarks and trade names are those of their respective owners.

ANATEL

Questions about your JBL Clip 3 ? Post in the comments!
Download JBL Clip 3 Manual [PDF]

JBL Charge4 Manual

JBL Charge4

JBL Charge4 User Manual

1. WHAT’S IN THE BOX

WHAT’S IN THE BOX

2. Bluetooth pairing

 

Bluetooth pairing

 

3. Play

Play

 

4. Connect

Connect

 

5. Charge: IPX7To preserve battery lifespan, fully charge at least once every 45 days.

Charge

 

6. Recharge

Recharge

 

7. Water Proof: Ensure the cap is well sealed before exposing to liquids.

Water Proof

 

8. Warning

Warning

WHAT’S IN THE BOX

Bluetooth pairing Play connect + charge warning!

To preserve battery lifespan, fully charge at least once every 45 days.Ensure the cap is well sealed before exposing to liquids.

9. Specifications

Transducer : 12mm
Frequency response : 20Hz-20kHz
Signal-to-noise ratio : 90dB
Maximum SPL : [email protected] Hz
Sensitivity : @1kHz dBFS/pa: -200B
Impedance : 16ohm
Bluetooth Max Output Power : 0 dBm
Bluetooth transmitter modulation : GFSK, /4DQPSK,8DPSK
Bluetooth transmitter frequency range : 2.402GHz-2.48GHz
Bluetooth profile : HFP v1.6, HSP v1.2, A2DP v1.2, AVRCP v1.5
Bluetooth version : xxx
Battery type Lithium-ion polymer : (3.7V, 120mAh)
Charging Time : 2H
Play time with Bluetooth on : up to 8H
Talk time with Bluetooth on : up to 8H

ANATEL

Bluetooth

The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by HARMAN International Industries, Incorporated is under license. Other trademarks and trade names are those of their respective owners.

Questions about your JBL Charge4 ? Post in the comments!
Download JBL Charge4 Manual [PDF]